< img height="1" width="1" style="display:none" src="https://www.facebook.com/tr?id=2042618782839916&ev=PageView&noscript=1" />
Diesel Engines & Parts
Weichai WP12 WD618 Water Pump 1000271133 Diesel Engine Parts
Weichai WP12 WD618 Water Pump 1000271133 Diesel Engine Parts
Weichai WP12 WD618 Water Pump 1000271133 Diesel Engine Parts

Weichai WP12 WD618 Water Pump 1000271133 Diesel Engine Parts

Model: WP12 / WD618

Part Number: 1000271133

Brands: Weichai Power

Engine Model: WP12, WD12, WD618, WP12.430, WP12.460

Engine Type: Diesel

Scope of application: heavy trucks, mining dump trucks, construction machinery, marine and generator engines

A numeric pump number in the WP12 family

The WP12 and WD618 engines use both long numeric part numbers and shorter ones, and 1000271133 belongs to the first group. As with the other pump numbers in this family, the differences between them show up in the pulley and inlet arrangement rather than in the pumping element itself.

Confirm the engine plate and the old pump number before ordering. On engines that have been rebuilt or had the front cover replaced, the pulley offset may not match the original specification, and that is not visible from the part number alone.

What the pump actually has to do

A 12-litre diesel produces a large amount of heat at full load, and the coolant pump has to move enough volume to keep the head and liners within their operating range. The pump runs at engine speed, so its flow rises and falls with rpm, and the cooling system relies on the thermostat and radiator to balance that.

When the pump loses efficiency, the engine does not overheat at idle. It overheats under load, exactly when the truck is climbing or the machine is digging, and that pattern is the clue that separates a weak pump from a blocked radiator.

Construction and testing

The pump uses a cast iron housing, a cast impeller and a sealed bearing cartridge lubricated for life. The mechanical face seal is the part that fails first, which is why it is tested above operating pressure rather than only inspected.

  • Impeller clearance set for efficient flow without contact.
  • Bearing play measured at operating speed.
  • Seal integrity tested at pressure.
  • Flow test at rated speed against the original curve.

Failure symptoms

The weep hole under the housing is a deliberate design feature: it lets a failing seal drip where it can be seen instead of contaminating the bearing. A small drip is an early warning, not a nuisance to be ignored.

  • Weep from the drain hole or white crust on the block
  • Rumbling or squealing from the front of the engine
  • Pulley or fan wobble
  • Overheating under load with a healthy thermostat
  • Coolant smell after a run
  • Play in the pulley with the belt removed

Diagnosing overheating before replacing the pump

Overheating has several causes and the pump is only one of them. Check coolant level and condition, confirm the thermostat opens, clean the radiator core, test the fan drive and inspect the belt for slip before ordering a pump. Each of those checks takes minutes and can save an unnecessary part.

A useful field test is to feel the radiator top and bottom hoses once the engine is warm. A large difference points to restricted flow through the core rather than a weak pump, and cleaning the core solves the problem without any parts.

Installation sequence

Fit the pump to a clean surface with a new gasket, torque evenly and bleed the system fully. Most repeat failures after a pump replacement come from incomplete bleeding rather than from the part itself.

  1. Drain coolant and dispose of it responsibly.
  2. Remove the belt and inspect the tensioner.
  3. Clean the block face and fit a new gasket.
  4. Torque bolts evenly in a cross pattern.
  5. Refill and bleed until the thermostat opens.
  6. Run to temperature, recheck level and look for weep.

Belt alignment and bearing life

Check the belt path with a straight edge across the pulleys before fitting the new pump, and replace any tensioner or idler that shows play. A side-loaded bearing fails quickly, and the failure looks like a pump quality problem when it is really alignment.

Coolant quality

Scale, incorrect inhibitor concentration and contamination all attack the seal faces. Use the specified coolant mixture and replace it at the recommended interval rather than topping up indefinitely. On engines working in dusty conditions, check the radiator core regularly as well.

Choosing the correct pump

Match the engine plate, the old pump number and the pulley type. Road, industrial and marine versions can differ even when the body casting looks identical. A photo of the old pump beside a ruler resolves most of these cases before an order is placed.

FAQ

Does the pump include a gasket?

Yes, the gasket and O-ring are supplied.

Can I drive with a weeping pump?

Only to reach a workshop. Coolant loss leads to overheating.

Is the pulley included?

The pump comes with the hub.

How do I separate pump noise from belt noise?

Remove the belt and spin the pump by hand.

Related parts and categories

Browse the Weichai pump category, and pair the pump with the WP12 water pump 612630061060 or the WP12 oil pump 612600081127.

Description

Weichai WP12 Water Pump (1000271133). The coolant pump circulates flow through the block and head. Its impeller, seal and bearing are matched to the housing, and the pulley mounting sets belt alignment.

Check the fan drive and thermostat before condemning the pump. A restricted radiator produces the same temperature rise under load and costs less to check.

Numbers beginning 1000 come from the newer numeric series used for assemblies and later-production parts. This series replaced several earlier numbers, so a cross-reference check is worthwhile. On this engine, confirm the WP12 application against the engine plate before ordering.

Do not over-tension the belt. Excess tension loads the pump bearing directly and is a common cause of repeat failures.

Ordering note. If the old number has been superseded, the replacement number is quoted alongside the original so the purchasing file stays consistent.

Related reading: Cylinder Liner Cavitation: Causes, Symptoms and Prevention

We Are 30 Years Diesel Engine Parts Supplier
BrandEPID
Warranty12 Months
Condition100%New
More ModelsWeichai: WP12, WD12, WD618, WP12.430, WP12.460, and other Weichai series.
ShippingBy sea / air / express (DHL, FEDEX, TNT, UPS, EMS)
PackingStandard exporting packing or as required
Payment TermL/C, T/T, Western Union, Trade Assurance
Delivery Time3-7 days (depend on order)
Selling Point1. On-time Delivery   2. Genuine Quality Assurance   3. Professional Supplier

Construction and testing

The pump uses a cast iron housing, a cast impeller and a sealed bearing cartridge lubricated for life. The mechanical face seal is the part that fails first, which is why it is tested above operating pressure rather than only inspected.

  • Impeller clearance set for efficient flow without contact.
  • Bearing play measured at operating speed.
  • Seal integrity tested at pressure.
  • Flow test at rated speed against the original curve.

Failure symptoms

The weep hole under the housing is a deliberate design feature: it lets a failing seal drip where it can be seen instead of contaminating the bearing. A small drip is an early warning, not a nuisance to be ignored.

  • Weep from the drain hole or white crust on the block
  • Rumbling or squealing from the front of the engine
  • Pulley or fan wobble
  • Overheating under load with a healthy thermostat
  • Coolant smell after a run
  • Play in the pulley with the belt removed

Diagnosing overheating before replacing the pump

Overheating has several causes and the pump is only one of them. Check coolant level and condition, confirm the thermostat opens, clean the radiator core, test the fan drive and inspect the belt for slip before ordering a pump. Each of those checks takes minutes and can save an unnecessary part.

A useful field test is to feel the radiator top and bottom hoses once the engine is warm. A large difference points to restricted flow through the core rather than a weak pump, and cleaning the core solves the problem without any parts.

Installation sequence

Fit the pump to a clean surface with a new gasket, torque evenly and bleed the system fully. Most repeat failures after a pump replacement come from incomplete bleeding rather than from the part itself.

  1. Drain coolant and dispose of it responsibly.
  2. Remove the belt and inspect the tensioner.
  3. Clean the block face and fit a new gasket.
  4. Torque bolts evenly in a cross pattern.
  5. Refill and bleed until the thermostat opens.
  6. Run to temperature, recheck level and look for weep.

Belt alignment and bearing life

Check the belt path with a straight edge across the pulleys before fitting the new pump, and replace any tensioner or idler that shows play. A side-loaded bearing fails quickly, and the failure looks like a pump quality problem when it is really alignment.

Coolant quality

Scale, incorrect inhibitor concentration and contamination all attack the seal faces. Use the specified coolant mixture and replace it at the recommended interval rather than topping up indefinitely. On engines working in dusty conditions, check the radiator core regularly as well.

Choosing the correct pump

Match the engine plate, the old pump number and the pulley type. Road, industrial and marine versions can differ even when the body casting looks identical. A photo of the old pump beside a ruler resolves most of these cases before an order is placed.

Related parts and categories

Browse the Weichai pump category, and pair the pump with the WP12 water pump 612630061060 or the WP12 oil pump 612600081127.

Detailed picture

Weichai WP12 WD618 Water Pump 1000271133 Diesel Engine Parts
Weichai WP12 WD618 Water Pump 1000271133 Diesel Engine Parts
Weichai WP12 WD618 Water Pump 1000271133 Diesel Engine Parts

Q&A

  • Does the pump include a gasket?

    Yes, the gasket and O-ring are supplied.

  • Can I drive with a weeping pump?

    Only to reach a workshop. Coolant loss leads to overheating.

  • Is the pulley included?

    The pump comes with the hub.

  • How do I separate pump noise from belt noise?

    Remove the belt and spin the pump by hand.

Why buy from EPID

EPID supplies diesel engine parts for Weichai, Baudouin, Yuchai, Caterpillar, Sinotruk, FAW Xichai and Cummins engines. Every order is checked against the original part number before packing, and our team can identify a part from a photo of the engine plate. Ask for a quotation with your model and quantity and we will reply within one working day.

send message

    • [recaptcha]

    Home Tel Mail Inquiry