< img height="1" width="1" style="display:none" src="https://www.facebook.com/tr?id=2042618782839916&ev=PageView&noscript=1" />
Diesel Engines & Parts
Yuchai YC4108 Water Pump D0305-1307010A Diesel Engine Parts
Yuchai YC4108 Water Pump D0305-1307010A Diesel Engine Parts
Yuchai YC4108 Water Pump D0305-1307010A Diesel Engine Parts

Yuchai YC4108 Water Pump D0305-1307010A Diesel Engine Parts

Model: YC4108

Part Number: D0305-1307010A

Brands: Yuchai

Engine Model: YC4108

Engine Type: Diesel

Scope of application: light and medium trucks, agricultural machinery, generator sets, marine auxiliary

A second water pump variant for the YC4108

Yuchai used more than one coolant pump on the YC4108 depending on production period and accessory layout. Part D0305-1307010A is the alternative to D0305-1307020B, and the right one depends on the pulley and inlet arrangement fitted to the engine.

That detail matters more than it sounds. A pump with the correct casting but the wrong pulley offset will not align with the belt, and it destroys its own bearing within hours of running.

Applications and fitment

The pump fits YC4108 engines in trucks, agricultural machinery and gensets. Confirm the engine plate, the old pump number and the pulley diameter before ordering.

Construction and bench testing

  • Impeller clearance set for efficient flow.
  • Bearing play measured at operating speed.
  • Seal integrity tested above operating pressure.
  • Flow test at rated speed.

Failure symptoms

  • Weep from the drain hole
  • Rumbling or squealing from the front of the engine
  • Pulley wobble
  • Overheating under load
  • White residue around the pump
  • Play in the pulley with the belt off

Installation sequence

  1. Drain coolant and dispose of it responsibly.
  2. Remove the belt and inspect the tensioner.
  3. Clean the block face and fit a new gasket.
  4. Torque bolts evenly in a cross pattern.
  5. Refill and bleed the system.
  6. Run to temperature, recheck level and look for weep.

Choosing between the two pump variants

Compare the old pump with the new one: pulley diameter, inlet position and mounting face are the identifying features. Send a photo of the old pump beside a ruler and we will confirm which variant the engine needs.

Belt alignment and bearing life

Most premature failures trace back to belt alignment. A worn tensioner or the wrong pulley offset side-loads the bearing and the seal weeps within a few thousand hours. Check the belt path with a straight edge before fitting the new pump.

Radiator care in the field

Field work packs the radiator core with chaff and dust. Clean the core with compressed air at every major service; this prevents more overheating than any component replacement and costs nothing.

Coolant quality

Use the correct coolant mixture rather than plain water. Plain water scales the housing and radiator, reducing flow and shortening seal life.

Stock planning

Pumps are compact and do not deteriorate in storage. One spare pump with a gasket and a belt can turn a breakdown into a same-day repair.

Bleeding the cooling system

Trapped air is the most common reason an engine overheats immediately after a pump replacement. Fill slowly at the highest point, open the heater circuit if fitted, and run the engine with the cap off until the thermostat opens. Then top up, fit the cap and recheck after the first cool-down.

A system that needs repeated topping up has a leak. On a diesel the leak is often the early stage of a head gasket failure, so investigate rather than simply refilling.

Belt and tensioner check

Inspect the belt for glazing and cracks, and check the tensioner for a rough bearing. A worn tensioner side-loads the new pump and undoes the repair. Re-tension the belt after the first heat cycle, because a new belt stretches slightly.

Coolant type and mixing

Mixing coolant brands or topping up with water repeatedly reduces inhibitor protection and allows scale to form in the pump housing and radiator. Drain and refill with a single correctly mixed coolant rather than topping up indefinitely. On a machine that works in the field, a clean system is cheaper than any component replacement.

Dispose of used coolant responsibly. It is toxic to animals and persists in soil, which matters on farms where the engine is serviced outdoors.

Checking the thermostat housing and hoses

While the pump is off, inspect the thermostat housing for corrosion and the hoses for internal delamination. A hose that has broken down inside restricts flow and looks healthy from outside. Replace any hose that is soft, swollen or more than a few years old.

Use the correct clamps rather than wire types. A clamp that does not distribute load evenly cuts into the hose and produces a leak that appears only when the system is hot and pressurised.

Why the pump is often replaced too late

Coolant pumps rarely fail suddenly; they fade. By the time the engine is overheating on a warm day, the bearing and seal have usually been deteriorating for months. Replacing the pump at the first sign of weep or noise is far cheaper than dealing with a warped head afterwards.

FAQ

How do I choose between this pump and D0305-1307020B?

Compare the pulley and inlet arrangement, or send us a photo of the old pump.

Does the pump include a gasket?

Yes, the gasket is supplied.

Can I run with a leaking pump?

Only to reach a workshop.

Is the pulley included?

The pump comes with the hub.

Related parts and categories

Browse the Yuchai pump category, and pair the pump with the YC4108 water pump D0305-1307020B or the YC4108 oil pump D30-1011100.

Description

Yuchai YC4108 Water Pump (1307010). The coolant pump circulates flow through the block and head. Its impeller, seal and bearing are matched to the housing, and the pulley mounting sets belt alignment.

Confirm the inlet angle and hose spigot position against the old pump. Two pumps can share a housing and differ in the direction the hose leaves.

Numbers beginning 1307 are used on WP6 and WP7 engines. The suffix, not the leading digits, distinguishes the variants. On this engine, confirm the YC4108 application against the engine plate before ordering.

Drain and refill with the correct coolant mix and bleed the system completely. Air in the system causes hot spots and accelerates cavitation damage on the liners.

Ordering note. Warranty is twelve months against manufacturing defects. Failures caused by incorrect clearance, overheating or debris are assessed on the returned part rather than refused outright.

Related reading: Cylinder Liner Cavitation: Causes, Symptoms and Prevention

We Are 30 Years Diesel Engine Parts Supplier
BrandEPID
Warranty12 Months
Condition100%New
More ModelsWeichai: YC4108, and other Weichai series.
ShippingBy sea / air / express (DHL, FEDEX, TNT, UPS, EMS)
PackingStandard exporting packing or as required
Payment TermL/C, T/T, Western Union, Trade Assurance
Delivery Time3-7 days (depend on order)
Selling Point1. On-time Delivery   2. Genuine Quality Assurance   3. Professional Supplier

Construction and bench testing

  • Impeller clearance set for efficient flow.
  • Bearing play measured at operating speed.
  • Seal integrity tested above operating pressure.
  • Flow test at rated speed.

Failure symptoms

  • Weep from the drain hole
  • Rumbling or squealing from the front of the engine
  • Pulley wobble
  • Overheating under load
  • White residue around the pump
  • Play in the pulley with the belt off

Installation sequence

  1. Drain coolant and dispose of it responsibly.
  2. Remove the belt and inspect the tensioner.
  3. Clean the block face and fit a new gasket.
  4. Torque bolts evenly in a cross pattern.
  5. Refill and bleed the system.
  6. Run to temperature, recheck level and look for weep.

Choosing between the two pump variants

Compare the old pump with the new one: pulley diameter, inlet position and mounting face are the identifying features. Send a photo of the old pump beside a ruler and we will confirm which variant the engine needs.

Belt alignment and bearing life

Most premature failures trace back to belt alignment. A worn tensioner or the wrong pulley offset side-loads the bearing and the seal weeps within a few thousand hours. Check the belt path with a straight edge before fitting the new pump.

Radiator care in the field

Field work packs the radiator core with chaff and dust. Clean the core with compressed air at every major service; this prevents more overheating than any component replacement and costs nothing.

Coolant quality

Use the correct coolant mixture rather than plain water. Plain water scales the housing and radiator, reducing flow and shortening seal life.

Stock planning

Pumps are compact and do not deteriorate in storage. One spare pump with a gasket and a belt can turn a breakdown into a same-day repair.

Bleeding the cooling system

Trapped air is the most common reason an engine overheats immediately after a pump replacement. Fill slowly at the highest point, open the heater circuit if fitted, and run the engine with the cap off until the thermostat opens. Then top up, fit the cap and recheck after the first cool-down.

A system that needs repeated topping up has a leak. On a diesel the leak is often the early stage of a head gasket failure, so investigate rather than simply refilling.

Belt and tensioner check

Inspect the belt for glazing and cracks, and check the tensioner for a rough bearing. A worn tensioner side-loads the new pump and undoes the repair. Re-tension the belt after the first heat cycle, because a new belt stretches slightly.

Coolant type and mixing

Mixing coolant brands or topping up with water repeatedly reduces inhibitor protection and allows scale to form in the pump housing and radiator. Drain and refill with a single correctly mixed coolant rather than topping up indefinitely. On a machine that works in the field, a clean system is cheaper than any component replacement.

Dispose of used coolant responsibly. It is toxic to animals and persists in soil, which matters on farms where the engine is serviced outdoors.

Checking the thermostat housing and hoses

While the pump is off, inspect the thermostat housing for corrosion and the hoses for internal delamination. A hose that has broken down inside restricts flow and looks healthy from outside. Replace any hose that is soft, swollen or more than a few years old.

Use the correct clamps rather than wire types. A clamp that does not distribute load evenly cuts into the hose and produces a leak that appears only when the system is hot and pressurised.

Why the pump is often replaced too late

Coolant pumps rarely fail suddenly; they fade. By the time the engine is overheating on a warm day, the bearing and seal have usually been deteriorating for months. Replacing the pump at the first sign of weep or noise is far cheaper than dealing with a warped head afterwards.

Related parts and categories

Browse the Yuchai pump category, and pair the pump with the YC4108 water pump D0305-1307020B or the YC4108 oil pump D30-1011100.

Detailed picture

Yuchai YC4108 Water Pump D0305-1307010A Diesel Engine Parts
Yuchai YC4108 Water Pump D0305-1307010A Diesel Engine Parts
Yuchai YC4108 Water Pump D0305-1307010A Diesel Engine Parts

Q&A

  • How do I choose between this pump and D0305-1307020B?

    Compare the pulley and inlet arrangement, or send us a photo of the old pump.

  • Does the pump include a gasket?

    Yes, the gasket is supplied.

  • Can I run with a leaking pump?

    Only to reach a workshop.

  • Is the pulley included?

    The pump comes with the hub.

Why buy from EPID

EPID supplies diesel engine parts for Weichai, Baudouin, Yuchai, Caterpillar, Sinotruk, FAW Xichai and Cummins engines. Every order is checked against the original part number before packing. Ask for a quotation with your model and quantity and we will reply within one working day.

send message

    • [recaptcha]

    Home Tel Mail Inquiry