< img height="1" width="1" style="display:none" src="https://www.facebook.com/tr?id=2042618782839916&ev=PageView&noscript=1" />
Diesel Engines & Parts
Weichai WP7 WP8 Cylinder Liner 1003150194 Diesel Engine Parts
Weichai WP7 WP8 Cylinder Liner 1003150194 Diesel Engine Parts

Weichai WP7 WP8 Cylinder Liner 1003150194 Diesel Engine Parts

Model: WP7 / WP8

Part Number: 1003150194

Brands: Weichai Power

Engine Model: WP7, WP7H, WP8, WP8H

Engine Type: Diesel

Scope of application: medium and heavy trucks, buses, construction machinery, generator sets

Liner numbers in the WP7 and WP8 family

The WP7 and WP8 engines carry more than one cylinder liner number, and 1003150194 is one of them alongside 610800010503. The differences are usually in flange thickness or O-ring groove position, tied to a production revision of the block rather than to the bore itself. A liner that sits at the wrong height causes head gasket failure even when everything else is correct.

The liner as the working surface

The liner is the wall the piston rings run against. It contains combustion pressure, conducts heat into the coolant and provides the upper sealing surface for the head gasket. Once the honed cross hatch has polished away, rings cannot retain oil and the bore begins to scuff.

Bore finish and checks

Liners are centrifugally cast, machined and plateau honed. Checks before packing cover the dimensions that decide sealing and oil control.

  • Bore diameter and ovality measured at three heights.
  • Plateau finish verified against specification.
  • Flange thickness checked for correct protrusion.
  • O-ring groove inspected for damage.

Symptoms of worn liners

Oil consumption is usually the first complaint, followed by smoke at start-up and increasing crankcase pressure. If the bore has a ridge at the top of ring travel, the liner must be replaced rather than honed.

  • Oil consumption rising without external leaks
  • Blue smoke at cold start
  • Blow-by pushing oil out of the breather
  • Glazed or vertically scored bores
  • Ring end gaps far beyond specification
  • Coolant in the oil after an O-ring failure

Fitting the liners

  1. Clean the block bores to bare metal.
  2. Fit new O-rings with assembly grease.
  3. Measure protrusion with a dial gauge.
  4. Hold the liner down while turning the crank.
  5. Check piston clearance before fitting rings.
  6. Follow the ring break-in procedure afterwards.

Protrusion and head gasket sealing

Protrusion is the small height the liner stands above the deck. It lets the fire ring crush onto the liner top and seal combustion pressure. Too low and gas escapes into the coolant; uneven across cylinders and the gasket is clamped unevenly. Never compensate by over-torquing head bolts.

Measuring bore wear

Measure with a bore gauge at three heights and two directions to find ovality and taper. A bore that is oval beyond the service limit will not seal new rings, and honing only removes material without restoring roundness.

Coolant and cavitation

Wet liners vibrate against the coolant and can suffer cavitation pitting when coolant chemistry is neglected. Correct coolant mixture and a maintained cooling system are the defence.

Matching liners, pistons and rings

Order the liner, piston and ring as a matched set where possible. A liner honed for one ring type may not suit another brand, and mixing parts is the most common cause of oil consumption after a rebuild.

Maintenance for liner life

Keep coolant chemistry in range, change oil at the severe-duty interval and keep the air filter clean. Dust ingress wears a liner faster than any other single cause.

Removing old liners

Use the correct puller rather than driving liners out with a hammer, which distorts the block bore and ruins the seat for the new liner. Scrape the seat and O-ring grooves to bright metal after removal and inspect for pitting where the O-rings sit.

Bore measurement and ovality limits

Measure at three heights and two directions to find ovality and taper. A bore oval beyond the service limit will not seal new rings, and honing removes material without restoring roundness. Record the figures for each cylinder, because the difference between cylinders matters as much as the absolute wear.

Storing liners before assembly

Liners are supplied oiled and wrapped because a bare bore corrodes quickly. Keep them packaged until the block is clean, and do not polish surface rust with abrasive paper, which destroys the honed finish rings need to seat against.

Removing old liners safely

Use the correct puller rather than driving liners out with a hammer, which distorts the block bore and ruins the seat for the new liner. Scrape the seat and O-ring grooves to bright metal after removal and inspect for pitting where the O-rings sit. A pitted seat leaks coolant even with new O-rings.

Protrusion and gasket sealing

Protrusion is the small height the liner stands above the deck. It lets the fire ring crush onto the liner top and seal combustion pressure. Uneven protrusion across cylinders is a common cause of head gasket failure on engines that were otherwise assembled correctly.

Coolant and cavitation

Wet liners vibrate against the coolant and can suffer cavitation pitting when coolant chemistry is neglected. Correct mixture and a maintained cooling system are the only defence.

FAQ

Are O-rings included?

Yes, the correct set for the block bore is supplied.

Do new liners need honing?

No. They are supplied plateau honed.

Can I replace one liner only?

Possible, but a full set keeps compression balanced.

What causes pitting?

Cavitation from incorrect coolant or air in the system.

Related parts and categories

Browse the Weichai cylinder liner category, and pair the liner with the WP7 and WP8 cylinder liner 610800010503 or the WP7 cylinder block 1000267735.

Description

Weichai WP7 Cylinder Liner (1003150194). Bore roundness and surface finish are set by this component. A plateau-honed liner holds oil while the rings bed in, which is what controls oil use during the first hours of running.

Confirm the flange thickness and outside diameter against the block you are fitting to. Liner seats were revised, and a liner from the wrong revision will not protrude correctly.

Numbers beginning 1003 belong to the numeric series used across WP7, WP8 and WP9. The engine plate is the fastest way to confirm which revision applies. On this engine, confirm the WP7 application against the engine plate before ordering.

Scrape the liner seat and O-ring groove to bright metal and inspect for pitting. A pitted seat leaks even with new seals, usually weeks later after several heat cycles.

Ordering note. Packing is export grade: each unit is wrapped, boxed and palletised for sea freight, with the part number marked on the outside so the receiving store can book it in without opening the carton.

Related reading: Cylinder Liner Cavitation: Causes, Symptoms and Prevention

We Are 30 Years Diesel Engine Parts Supplier
BrandEPID
Warranty12 Months
Condition100%New
More ModelsWeichai: WP7, WP7H, WP8, WP8H, and other Weichai series.
ShippingBy sea / air / express (DHL, FEDEX, TNT, UPS, EMS)
PackingStandard exporting packing or as required
Payment TermL/C, T/T, Western Union, Trade Assurance
Delivery Time3-7 days (depend on order)
Selling Point1. On-time Delivery   2. Genuine Quality Assurance   3. Professional Supplier

Bore finish and checks

Liners are centrifugally cast, machined and plateau honed. Checks before packing cover the dimensions that decide sealing and oil control.

  • Bore diameter and ovality measured at three heights.
  • Plateau finish verified against specification.
  • Flange thickness checked for correct protrusion.
  • O-ring groove inspected for damage.

Symptoms of worn liners

Oil consumption is usually the first complaint, followed by smoke at start-up and increasing crankcase pressure. If the bore has a ridge at the top of ring travel, the liner must be replaced rather than honed.

  • Oil consumption rising without external leaks
  • Blue smoke at cold start
  • Blow-by pushing oil out of the breather
  • Glazed or vertically scored bores
  • Ring end gaps far beyond specification
  • Coolant in the oil after an O-ring failure

Fitting the liners

  1. Clean the block bores to bare metal.
  2. Fit new O-rings with assembly grease.
  3. Measure protrusion with a dial gauge.
  4. Hold the liner down while turning the crank.
  5. Check piston clearance before fitting rings.
  6. Follow the ring break-in procedure afterwards.

Protrusion and head gasket sealing

Protrusion is the small height the liner stands above the deck. It lets the fire ring crush onto the liner top and seal combustion pressure. Too low and gas escapes into the coolant; uneven across cylinders and the gasket is clamped unevenly. Never compensate by over-torquing head bolts.

Measuring bore wear

Measure with a bore gauge at three heights and two directions to find ovality and taper. A bore that is oval beyond the service limit will not seal new rings, and honing only removes material without restoring roundness.

Coolant and cavitation

Wet liners vibrate against the coolant and can suffer cavitation pitting when coolant chemistry is neglected. Correct coolant mixture and a maintained cooling system are the defence.

Matching liners, pistons and rings

Order the liner, piston and ring as a matched set where possible. A liner honed for one ring type may not suit another brand, and mixing parts is the most common cause of oil consumption after a rebuild.

Maintenance for liner life

Keep coolant chemistry in range, change oil at the severe-duty interval and keep the air filter clean. Dust ingress wears a liner faster than any other single cause.

Removing old liners

Use the correct puller rather than driving liners out with a hammer, which distorts the block bore and ruins the seat for the new liner. Scrape the seat and O-ring grooves to bright metal after removal and inspect for pitting where the O-rings sit.

Bore measurement and ovality limits

Measure at three heights and two directions to find ovality and taper. A bore oval beyond the service limit will not seal new rings, and honing removes material without restoring roundness. Record the figures for each cylinder, because the difference between cylinders matters as much as the absolute wear.

Storing liners before assembly

Liners are supplied oiled and wrapped because a bare bore corrodes quickly. Keep them packaged until the block is clean, and do not polish surface rust with abrasive paper, which destroys the honed finish rings need to seat against.

Removing old liners safely

Use the correct puller rather than driving liners out with a hammer, which distorts the block bore and ruins the seat for the new liner. Scrape the seat and O-ring grooves to bright metal after removal and inspect for pitting where the O-rings sit. A pitted seat leaks coolant even with new O-rings.

Protrusion and gasket sealing

Protrusion is the small height the liner stands above the deck. It lets the fire ring crush onto the liner top and seal combustion pressure. Uneven protrusion across cylinders is a common cause of head gasket failure on engines that were otherwise assembled correctly.

Coolant and cavitation

Wet liners vibrate against the coolant and can suffer cavitation pitting when coolant chemistry is neglected. Correct mixture and a maintained cooling system are the only defence.

Related parts and categories

Browse the Weichai cylinder liner category, and pair the liner with the WP7 and WP8 cylinder liner 610800010503 or the WP7 cylinder block 1000267735.

Detailed picture

Weichai WP7 WP8 Cylinder Liner 1003150194 Diesel Engine Parts
Weichai WP7 WP8 Cylinder Liner 1003150194 Diesel Engine Parts

Q&A

  • Are O-rings included?

    Yes, the correct set for the block bore is supplied.

  • Do new liners need honing?

    No. They are supplied plateau honed.

  • Can I replace one liner only?

    Possible, but a full set keeps compression balanced.

  • What causes pitting?

    Cavitation from incorrect coolant or air in the system.

Why buy from EPID

EPID supplies diesel engine parts for Weichai, Baudouin, Yuchai, Caterpillar, Sinotruk, FAW Xichai and Cummins engines. Every order is checked against the original part number before packing, and our team can identify a part from a photo of the engine plate. Ask for a quotation with your model and quantity and we will reply within one working day.

send message

    • [recaptcha]

    Home Tel Mail Inquiry