

Model: WP7 / WP8
Part Number: 1003125852
Brands: Weichai Power
Engine Model: WP7, WP7H, WP8, WP8H
Engine Type: Diesel
Scope of application: medium and heavy trucks, buses, construction machinery, generator sets
The WP7 and WP8 use head castings that were revised over time, and 1003125852 sits alongside 1003125851 as one of those revisions. The difference between them is usually in the injector bore or in the coolant outlet position rather than in the overall shape, which makes them almost impossible to tell apart once fitted. That is exactly why the casting number is the only reliable identifier.
Confirm the engine plate and the old casting number before ordering. A head from the neighbouring revision will bolt up, run, and produce smoke or a coolant leak that nobody can trace back to the head.
Each head is cast, stress relieved and machined on the deck, valve seats, guides and injector bores. The checks that decide whether it will hold are dimensional and can be supplied on request.
Head failures begin with cooling. A restricted radiator or a tired pump raises metal temperature, the deck warps and the gasket loses its grip. The first symptoms are easily mistaken for injector problems, which is why a pressure test and a combustion gas test should come before any parts are ordered.
Preparation decides the outcome. Clean the block deck to bare metal, check flatness, and confirm the head bolts are new before starting.
A pressure test fills the water jacket above operating pressure and looks for loss. It finds cracks through the jacket and into a port, but not a deck that is warped yet still sealed. Flatness is measured separately with a straight edge, and both checks are needed before a head is fitted.
Light seat wear can be re-cut and a mildly warped deck machined once. Cracks between seats, at the injector bore or across the deck are not economically repairable, and a repaired head that fails again usually takes the gasket with it.
If the head is replaced because of valve damage, renew valves, springs and retainers as a set. Reusing springs that have lost tension with new valves produces a valve train that floats at high speed, which shows as a misfire under load rather than at idle.
Keep coolant at the correct concentration, clean the radiator core in dusty conditions and replace the thermostat on schedule. Packed cores raise temperature without any component fault, and a head that runs hot will warp regardless of how well it was machined.
Head bolts are torque-to-yield and must be replaced every time. Reusing them reduces clamping force and produces a leak at high load that looks like a gasket failure rather than a bolt problem.
Match the engine plate, the old casting number and the injector type. Send photographs of the old head and the nameplate and we will confirm the variant before shipping.
Measure the block deck and the head face with a straight edge and feeler gauge along the length and both diagonals. A deck out by more than the service limit must be machined, and no gasket compensates for it. Scrape both surfaces to bare metal and avoid rotary abrasive discs, which remove metal unevenly.
A pitted or carboned injector seat lets compression escape past the copper washer, producing a chuffing noise and a misfire that is hard to trace. Re-cut the seat while the head is on the bench, because doing it later means removing the head again.
Yes, unless a bare head is requested.
No. They must be replaced.
Pressure test and combustion gas test.
No. Confirm the casting number.
Browse the Weichai cylinder head category, and pair the head with the WP7 and WP8 cylinder head 1003125851 or the WP7 and WP8 cylinder head 1001396787.
Weichai WP7 Cylinder Head (1003125852). The head carries combustion pressure, the valve train and the injectors, and it has to seal all three against a block that expands at a different rate. It is the most highly stressed casting in the engine.
Confirm the injector bore depth matches the injectors in use. Shimming an injector to compensate for a different bore is a common shortcut that produces smoke and hard starting.
Numbers beginning 1003 belong to the numeric series used across WP7, WP8 and WP9. The engine plate is the fastest way to confirm which revision applies. On this engine, confirm the WP7 application against the engine plate before ordering.
Have the head checked for flatness and, where necessary, pressure tested before assembly. A crack that does not leak cold will open once the engine reaches temperature.
Ordering note. For fleet customers, a consolidated stock list can be quoted against the engine plates in service, which usually exposes duplicated part numbers across similar units.
Related reading: Cylinder Head Rebuild: Valves, Guides and Seats
| We Are 30 Years Diesel Engine Parts Supplier | |
| Brand | EPID |
| Warranty | 12 Months |
| Condition | 100%New |
| More Models | Weichai: WP7, WP7H, WP8, WP8H, and other Weichai series. |
| Shipping | By sea / air / express (DHL, FEDEX, TNT, UPS, EMS) |
| Packing | Standard exporting packing or as required |
| Payment Term | L/C, T/T, Western Union, Trade Assurance |
| Delivery Time | 3-7 days (depend on order) |
| Selling Point | 1. On-time Delivery 2. Genuine Quality Assurance 3. Professional Supplier |
Head failures begin with cooling. A restricted radiator or a tired pump raises metal temperature, the deck warps and the gasket loses its grip. The first symptoms are easily mistaken for injector problems, which is why a pressure test and a combustion gas test should come before any parts are ordered.
Preparation decides the outcome. Clean the block deck to bare metal, check flatness, and confirm the head bolts are new before starting.
A pressure test fills the water jacket above operating pressure and looks for loss. It finds cracks through the jacket and into a port, but not a deck that is warped yet still sealed. Flatness is measured separately with a straight edge, and both checks are needed before a head is fitted.
Light seat wear can be re-cut and a mildly warped deck machined once. Cracks between seats, at the injector bore or across the deck are not economically repairable, and a repaired head that fails again usually takes the gasket with it.
If the head is replaced because of valve damage, renew valves, springs and retainers as a set. Reusing springs that have lost tension with new valves produces a valve train that floats at high speed, which shows as a misfire under load rather than at idle.
Keep coolant at the correct concentration, clean the radiator core in dusty conditions and replace the thermostat on schedule. Packed cores raise temperature without any component fault, and a head that runs hot will warp regardless of how well it was machined.
Head bolts are torque-to-yield and must be replaced every time. Reusing them reduces clamping force and produces a leak at high load that looks like a gasket failure rather than a bolt problem.
Match the engine plate, the old casting number and the injector type. Send photographs of the old head and the nameplate and we will confirm the variant before shipping.
Measure the block deck and the head face with a straight edge and feeler gauge along the length and both diagonals. A deck out by more than the service limit must be machined, and no gasket compensates for it. Scrape both surfaces to bare metal and avoid rotary abrasive discs, which remove metal unevenly.
A pitted or carboned injector seat lets compression escape past the copper washer, producing a chuffing noise and a misfire that is hard to trace. Re-cut the seat while the head is on the bench, because doing it later means removing the head again.
Browse the Weichai cylinder head category, and pair the head with the WP7 and WP8 cylinder head 1003125851 or the WP7 and WP8 cylinder head 1001396787.


Yes, unless a bare head is requested.
No. They must be replaced.
Pressure test and combustion gas test.
No. Confirm the casting number.
EPID supplies diesel engine parts for Weichai, Baudouin, Yuchai, Caterpillar, Sinotruk, FAW Xichai and Cummins engines. Every order is checked against the original part number before packing, and our team can identify a part from a photo of the engine plate. Ask for a quotation with your model and quantity and we will reply within one working day.