< img height="1" width="1" style="display:none" src="https://www.facebook.com/tr?id=2042618782839916&ev=PageView&noscript=1" />
Diesel Engines & Parts
Weichai WP7 WP8 Cylinder Head 1001396787 Diesel Engine Parts
Weichai WP7 WP8 Cylinder Head 1001396787 Diesel Engine Parts

Weichai WP7 WP8 Cylinder Head 1001396787 Diesel Engine Parts

Model: WP7 / WP8

Part Number: 1001396787

Brands: Weichai Power

Engine Model: WP7, WP7H, WP8, WP8H

Engine Type: Diesel

Scope of application: medium and heavy trucks, buses, construction machinery, generator sets

Head numbers in the WP7 and WP8 family

Several cylinder head castings were used across the production life of these engines, and 1001396787 is one of them. Injector bore depth, port shape and coolant layout changed between generations, so a head from the wrong casting fits the block and changes combustion. Confirm the engine plate and the old casting number before ordering.

Casting and machining checks

Each head is cast, stress relieved and machined. The checks that decide whether it will hold are dimensional and can be supplied on request.

  • Deck flatness measured in both directions.
  • Valve seat width and concentricity.
  • Guide bore clearance for oil control.
  • Injector bore depth and seat angle.
  • Pressure test of water jacket and ports.

Symptoms that point to the head

Head failures usually begin with cooling. A restricted radiator or a tired pump raises metal temperature, the deck warps and the gasket loses its grip.

  • Coolant disappearing with no visible external leak
  • Bubbles in the radiator
  • White smoke after warm-up
  • Coolant in the oil
  • Compression loss on adjacent cylinders
  • Overheating with a healthy pump

Fitting the head

  1. Clean the block deck and check flatness.
  2. Fit a new gasket dry, without sealant.
  3. Torque in three stages, then angle tighten.
  4. Set valve clearance after the first heat cycle.
  5. Fill and bleed the cooling system.
  6. Recheck injector clamp torque after running.

Valve guides and oil consumption

Worn guides let oil down the stems, producing blue smoke at start-up that clears once the engine works. That pattern is often mistaken for worn rings. Measuring guide clearance on the bench settles the question.

Repair or replace

Light seat wear can be re-cut and a mildly warped deck machined once. Cracks between seats, at the injector bore or across the deck are not economically repairable.

Cooling system care

Keep coolant at the correct concentration, clean the radiator core in dusty conditions and replace the thermostat on schedule. Packed cores raise temperature without any component fault.

Head bolts

Head bolts are torque-to-yield and must be replaced every time. Reusing them reduces clamping force and produces a leak at high load that looks like a gasket failure.

Choosing the correct head

Match the engine plate, the old casting number and the injector type. Send photographs of the old head and the nameplate and we will confirm the variant.

Deck flatness before fitting

Measure the block deck and head face with a straight edge and feeler gauge along the length and both diagonals. A deck out by more than the service limit must be machined, and no gasket compensates for it.

What a pressure test finds and misses

A pressure test fills the water jacket above operating pressure and looks for loss. It finds cracks through the jacket and into a port, but not a deck that is warped yet still sealed. Flatness is measured separately with a straight edge, and both checks are needed before a head is fitted.

Valve train parts to renew with the head

If the head is replaced because of valve damage, renew valves, springs and retainers as a set. Reusing springs that have lost tension with new valves produces a valve train that floats at high speed, which shows as a misfire under load rather than at idle.

Deck preparation

Scrape the deck and head face to bare metal and wipe with a suitable solvent. Avoid rotary abrasive discs, which remove metal unevenly and change the flatness that was just measured.

Why head numbers change within a family

Head castings are revised when injector, port or coolant design changes. A head from another generation fits the block but changes combustion, and the resulting symptoms look like a fuel problem. The casting number and the injector seat are the features that identify the generation.

Repair or replace a head

Light valve seat wear can be re-cut and a mildly warped deck machined once if enough material remains. Cracks between seats, at the injector bore or across the deck are not economically repairable, and a repaired head that fails again usually takes the gasket with it.

Cooling system care

Keep coolant at the correct concentration, clean the radiator core in dusty conditions and replace the thermostat on schedule. Packed cores raise temperature without any component fault, and a head that runs hot will warp regardless of how well it was machined.

Head bolts and clamping load

Head bolts are torque-to-yield and must be replaced every time the head is removed. Reusing them reduces clamping force and produces a leak at high load that looks like a gasket failure.

FAQ

Does the head come with valves?

Yes, unless a bare head is requested.

Can I reuse the head bolts?

No. They must be replaced.

How do I confirm a crack?

Pressure test and combustion gas test.

Are heads interchangeable?

No. Confirm the casting number.

Related parts and categories

Browse the Weichai cylinder head category, and pair the head with the WP7 and WP8 cylinder head 1003785218 or the WP7 and WP8 full gasket kit 1001514985.

Description

Weichai WP7 Cylinder Head (1001396787). Every combustion event loads this casting. The fire ring seals against it, the injectors seat in it and the valves operate inside it, so wear or distortion here shows up as smoke, misfire or coolant loss.

Photograph the deck, the casting number and the old gasket. Those three images usually identify the revision before anything ships, and they are far cheaper than a returned head.

Numbers beginning 1001 belong to the numeric series introduced as the older 61xx numbers were superseded. Both numbers may describe the same physical part. On this engine, confirm the WP7 application against the engine plate before ordering.

Have the head checked for flatness and, where necessary, pressure tested before assembly. A crack that does not leak cold will open once the engine reaches temperature.

Ordering note. Photographs of the actual unit can be sent before dispatch on request. That is the cheapest way to avoid a return when a casting revision is in doubt.

Related reading: Cylinder Head Rebuild: Valves, Guides and Seats

We Are 30 Years Diesel Engine Parts Supplier
BrandEPID
Warranty12 Months
Condition100%New
More ModelsWeichai: WP7, WP7H, WP8, WP8H, and other Weichai series.
ShippingBy sea / air / express (DHL, FEDEX, TNT, UPS, EMS)
PackingStandard exporting packing or as required
Payment TermL/C, T/T, Western Union, Trade Assurance
Delivery Time3-7 days (depend on order)
Selling Point1. On-time Delivery   2. Genuine Quality Assurance   3. Professional Supplier

Symptoms that point to the head

Head failures usually begin with cooling. A restricted radiator or a tired pump raises metal temperature, the deck warps and the gasket loses its grip.

  • Coolant disappearing with no visible external leak
  • Bubbles in the radiator
  • White smoke after warm-up
  • Coolant in the oil
  • Compression loss on adjacent cylinders
  • Overheating with a healthy pump

Fitting the head

  1. Clean the block deck and check flatness.
  2. Fit a new gasket dry, without sealant.
  3. Torque in three stages, then angle tighten.
  4. Set valve clearance after the first heat cycle.
  5. Fill and bleed the cooling system.
  6. Recheck injector clamp torque after running.

Valve guides and oil consumption

Worn guides let oil down the stems, producing blue smoke at start-up that clears once the engine works. That pattern is often mistaken for worn rings. Measuring guide clearance on the bench settles the question.

Repair or replace

Light seat wear can be re-cut and a mildly warped deck machined once. Cracks between seats, at the injector bore or across the deck are not economically repairable.

Cooling system care

Keep coolant at the correct concentration, clean the radiator core in dusty conditions and replace the thermostat on schedule. Packed cores raise temperature without any component fault.

Head bolts

Head bolts are torque-to-yield and must be replaced every time. Reusing them reduces clamping force and produces a leak at high load that looks like a gasket failure.

Choosing the correct head

Match the engine plate, the old casting number and the injector type. Send photographs of the old head and the nameplate and we will confirm the variant.

Deck flatness before fitting

Measure the block deck and head face with a straight edge and feeler gauge along the length and both diagonals. A deck out by more than the service limit must be machined, and no gasket compensates for it.

What a pressure test finds and misses

A pressure test fills the water jacket above operating pressure and looks for loss. It finds cracks through the jacket and into a port, but not a deck that is warped yet still sealed. Flatness is measured separately with a straight edge, and both checks are needed before a head is fitted.

Valve train parts to renew with the head

If the head is replaced because of valve damage, renew valves, springs and retainers as a set. Reusing springs that have lost tension with new valves produces a valve train that floats at high speed, which shows as a misfire under load rather than at idle.

Deck preparation

Scrape the deck and head face to bare metal and wipe with a suitable solvent. Avoid rotary abrasive discs, which remove metal unevenly and change the flatness that was just measured.

Why head numbers change within a family

Head castings are revised when injector, port or coolant design changes. A head from another generation fits the block but changes combustion, and the resulting symptoms look like a fuel problem. The casting number and the injector seat are the features that identify the generation.

Repair or replace a head

Light valve seat wear can be re-cut and a mildly warped deck machined once if enough material remains. Cracks between seats, at the injector bore or across the deck are not economically repairable, and a repaired head that fails again usually takes the gasket with it.

Cooling system care

Keep coolant at the correct concentration, clean the radiator core in dusty conditions and replace the thermostat on schedule. Packed cores raise temperature without any component fault, and a head that runs hot will warp regardless of how well it was machined.

Head bolts and clamping load

Head bolts are torque-to-yield and must be replaced every time the head is removed. Reusing them reduces clamping force and produces a leak at high load that looks like a gasket failure.

Related parts and categories

Browse the Weichai cylinder head category, and pair the head with the WP7 and WP8 cylinder head 1003785218 or the WP7 and WP8 full gasket kit 1001514985.

Detailed picture

Weichai WP7 WP8 Cylinder Head 1001396787 Diesel Engine Parts
Weichai WP7 WP8 Cylinder Head 1001396787 Diesel Engine Parts

Q&A

  • Does the head come with valves?

    Yes, unless a bare head is requested.

  • Can I reuse the head bolts?

    No. They must be replaced.

  • How do I confirm a crack?

    Pressure test and combustion gas test.

  • Are heads interchangeable?

    No. Confirm the casting number.

Why buy from EPID

EPID supplies diesel engine parts for Weichai, Baudouin, Yuchai, Caterpillar, Sinotruk, FAW Xichai and Cummins engines. Every order is checked against the original part number before packing, and our team can identify a part from a photo of the engine plate. Ask for a quotation with your model and quantity and we will reply within one working day.

send message

    • [recaptcha]

    Home Tel Mail Inquiry