< img height="1" width="1" style="display:none" src="https://www.facebook.com/tr?id=2042618782839916&ev=PageView&noscript=1" />
Diesel Engines & Parts
Weichai WP7 WP8 Cylinder Head 1003785218 Diesel Engine Parts
Weichai WP7 WP8 Cylinder Head 1003785218 Diesel Engine Parts

Weichai WP7 WP8 Cylinder Head 1003785218 Diesel Engine Parts

Model: WP7 / WP8

Part Number: 1003785218

Brands: Weichai Power

Engine Model: WP7, WP7H, WP8, WP8H

Engine Type: Diesel

Scope of application: medium and heavy trucks, buses, construction machinery, generator sets

The head on the WP7 and WP8

The cylinder head closes the combustion chamber, carries the valve train and routes coolant around the injector and valve bridges. Part 1003785218 is one of the heads used on these engines, and it is the part where combustion pressure meets the cooling system.

When a head warps or cracks, coolant enters the cylinder or compression enters the water jacket. The symptoms are easy to misread: white smoke, coolant loss with no external leak and overheating under load are all typical.

Head variants on these engines

Weichai used more than one head casting on the WP7 and WP8 across production periods. Injector bore depth and port detail differ, so confirm the engine plate and the old casting number before ordering. A head from the wrong generation fits but changes combustion and produces hard starting.

Casting and machining checks

Each head is cast in high-grade iron, stress relieved and machined. The checks that decide whether it will hold are all dimensional, and the measurements can be supplied on request.

  • Deck flatness measured in both directions.
  • Valve seat width and concentricity.
  • Guide bore clearance for oil control.
  • Injector bore depth and seat angle.
  • Pressure test of water jacket and exhaust ports.

Symptoms that point to the head

Head failures usually begin with cooling. A restricted radiator or a tired water pump raises metal temperature, the deck warps and the gasket loses its grip. The early symptoms are easily mistaken for injector problems.

  • Coolant disappearing with no visible external leak
  • Bubbles in the radiator or coolant pushed out of the filler
  • White smoke that persists after warm-up
  • Coolant in the oil, visible as a milky dipstick
  • Compression loss on two adjacent cylinders
  • Overheating that returns after a thermostat replacement

Fitting the new head

Preparation decides the outcome. Clean the block deck to bare metal, check flatness with a straight edge and a feeler gauge, and confirm that the head bolts are new before starting.

  1. Fit a new gasket dry, without sealant.
  2. Torque in three stages in the factory sequence, then angle tighten.
  3. Set valve clearance after the engine has run and cooled.
  4. Fill and bleed the cooling system with the specified mixture.
  5. Recheck injector clamp torque after the first hours of running.

Valve guides and oil consumption

Worn guides let oil down the stems, producing blue smoke at start-up that clears once the engine works. That pattern is often mistaken for worn rings, and the rebuild then goes in the wrong direction. Measuring guide clearance on the bench takes minutes and settles the question before parts are ordered.

Repair or replace

Light seat wear can be re-cut and a mildly warped deck machined once if enough material remains. Cracks between seats, at the injector bore or across the deck are not economically repairable, and a repaired head that fails again usually takes the gasket with it.

Cooling system care

Keep coolant at the correct concentration, clean the radiator core in dusty conditions and replace the thermostat on schedule. On engines that work in construction or agriculture, the core is often packed with dust, which raises temperature without any component fault.

Head bolts and clamping load

Head bolts are torque-to-yield and must be replaced every time the head is removed. Reusing them reduces clamping force, and the gasket then leaks at high load. Order a new bolt set with every head rather than discovering the need halfway through assembly.

Choosing the correct head

Match the engine plate, the old casting number and the injector type. Send photographs of the old head and the nameplate and our team will confirm the variant before shipping, which is much cheaper than returning a head from an overseas port.

Deck flatness before fitting

Measure the block deck and the head face with a straight edge and feeler gauge along the length and both diagonals. A deck out by more than the service limit must be machined, and no gasket compensates for it. Record the measurement so the next overhaul has a reference point.

Why head numbers change within a family

Head castings are revised when injector, port or coolant design changes. A head from another generation fits the block but changes combustion, and the resulting symptoms look like a fuel problem. The casting number and the injector seat are the two features that identify the generation.

Pressure testing explained

A pressure test fills the water jacket above operating pressure and looks for loss. It finds cracks through the jacket and into a port, but it does not find a deck that is warped yet still sealed. Flatness is measured separately with a straight edge, and both checks are needed.

FAQ

Does the head come with valves?

Yes, unless a bare head is requested.

Can I reuse the head bolts?

No. They must be replaced every time.

How do I confirm a crack?

A pressure test and a combustion gas test confirm it.

Are heads interchangeable between variants?

No. Confirm the casting number.

Related parts and categories

Browse the Weichai cylinder head category, and pair the head with the WP7 and WP8 full gasket kit 1001514985 or the WP8 cylinder block 1001854444.

Description

Weichai WP7 Cylinder Head (1003785218). Every combustion event loads this casting. The fire ring seals against it, the injectors seat in it and the valves operate inside it, so wear or distortion here shows up as smoke, misfire or coolant loss.

Confirm the injector bore depth matches the injectors in use. Shimming an injector to compensate for a different bore is a common shortcut that produces smoke and hard starting.

Numbers beginning 1003 belong to the numeric series used across WP7, WP8 and WP9. The engine plate is the fastest way to confirm which revision applies. On this engine, confirm the WP7 application against the engine plate before ordering.

Fit new head bolts every time. They are torque-to-yield fasteners and reusing them reduces clamping load exactly where the gasket needs it most, under load at working temperature.

Ordering note. Inspection reports can be provided for castings and crankshafts on request, covering the measurements taken before packing.

Related reading: Cylinder Head Rebuild: Valves, Guides and Seats

We Are 30 Years Diesel Engine Parts Supplier
BrandEPID
Warranty12 Months
Condition100%New
More ModelsWeichai: WP7, WP7H, WP8, WP8H, and other Weichai series.
ShippingBy sea / air / express (DHL, FEDEX, TNT, UPS, EMS)
PackingStandard exporting packing or as required
Payment TermL/C, T/T, Western Union, Trade Assurance
Delivery Time3-7 days (depend on order)
Selling Point1. On-time Delivery   2. Genuine Quality Assurance   3. Professional Supplier

Casting and machining checks

Each head is cast in high-grade iron, stress relieved and machined. The checks that decide whether it will hold are all dimensional, and the measurements can be supplied on request.

  • Deck flatness measured in both directions.
  • Valve seat width and concentricity.
  • Guide bore clearance for oil control.
  • Injector bore depth and seat angle.
  • Pressure test of water jacket and exhaust ports.

Symptoms that point to the head

Head failures usually begin with cooling. A restricted radiator or a tired water pump raises metal temperature, the deck warps and the gasket loses its grip. The early symptoms are easily mistaken for injector problems.

  • Coolant disappearing with no visible external leak
  • Bubbles in the radiator or coolant pushed out of the filler
  • White smoke that persists after warm-up
  • Coolant in the oil, visible as a milky dipstick
  • Compression loss on two adjacent cylinders
  • Overheating that returns after a thermostat replacement

Fitting the new head

Preparation decides the outcome. Clean the block deck to bare metal, check flatness with a straight edge and a feeler gauge, and confirm that the head bolts are new before starting.

  1. Fit a new gasket dry, without sealant.
  2. Torque in three stages in the factory sequence, then angle tighten.
  3. Set valve clearance after the engine has run and cooled.
  4. Fill and bleed the cooling system with the specified mixture.
  5. Recheck injector clamp torque after the first hours of running.

Valve guides and oil consumption

Worn guides let oil down the stems, producing blue smoke at start-up that clears once the engine works. That pattern is often mistaken for worn rings, and the rebuild then goes in the wrong direction. Measuring guide clearance on the bench takes minutes and settles the question before parts are ordered.

Repair or replace

Light seat wear can be re-cut and a mildly warped deck machined once if enough material remains. Cracks between seats, at the injector bore or across the deck are not economically repairable, and a repaired head that fails again usually takes the gasket with it.

Cooling system care

Keep coolant at the correct concentration, clean the radiator core in dusty conditions and replace the thermostat on schedule. On engines that work in construction or agriculture, the core is often packed with dust, which raises temperature without any component fault.

Head bolts and clamping load

Head bolts are torque-to-yield and must be replaced every time the head is removed. Reusing them reduces clamping force, and the gasket then leaks at high load. Order a new bolt set with every head rather than discovering the need halfway through assembly.

Choosing the correct head

Match the engine plate, the old casting number and the injector type. Send photographs of the old head and the nameplate and our team will confirm the variant before shipping, which is much cheaper than returning a head from an overseas port.

Deck flatness before fitting

Measure the block deck and the head face with a straight edge and feeler gauge along the length and both diagonals. A deck out by more than the service limit must be machined, and no gasket compensates for it. Record the measurement so the next overhaul has a reference point.

Why head numbers change within a family

Head castings are revised when injector, port or coolant design changes. A head from another generation fits the block but changes combustion, and the resulting symptoms look like a fuel problem. The casting number and the injector seat are the two features that identify the generation.

Pressure testing explained

A pressure test fills the water jacket above operating pressure and looks for loss. It finds cracks through the jacket and into a port, but it does not find a deck that is warped yet still sealed. Flatness is measured separately with a straight edge, and both checks are needed.

Related parts and categories

Browse the Weichai cylinder head category, and pair the head with the WP7 and WP8 full gasket kit 1001514985 or the WP8 cylinder block 1001854444.

Detailed picture

Weichai WP7 WP8 Cylinder Head 1003785218 Diesel Engine Parts
Weichai WP7 WP8 Cylinder Head 1003785218 Diesel Engine Parts

Q&A

  • Does the head come with valves?

    Yes, unless a bare head is requested.

  • Can I reuse the head bolts?

    No. They must be replaced every time.

  • How do I confirm a crack?

    A pressure test and a combustion gas test confirm it.

  • Are heads interchangeable between variants?

    No. Confirm the casting number.

Why buy from EPID

EPID supplies diesel engine parts for Weichai, Baudouin, Yuchai, Caterpillar, Sinotruk, FAW Xichai and Cummins engines. Every order is checked against the original part number before packing, and our team can identify a part from a photo of the engine plate. Ask for a quotation with your model and quantity and we will reply within one working day.

send message

    • [recaptcha]

    Home Tel Mail Inquiry