

Model: WP7 / WP8
Part Number: 610800030040
Brands: Weichai Power
Engine Model: WP7, WP7H, WP8, WP8H
Engine Type: Diesel
Scope of application: medium and heavy trucks, buses, construction machinery, generator sets
The WP7 and WP8 engines use more than one connecting rod number, and 610800030040 is one of them alongside 610800030073. The differences are usually in weight class or small end bush diameter, tied to a production revision of the piston and pin.
That matters because rods are weight matched within a set. Fitting one rod from a different weight class produces vibration at speed and loads the main bearings unevenly, and the fault is hard to trace once the engine is assembled.
The connecting rod reverses load twice per revolution. It is pulled in tension by piston inertia, pushed in compression by combustion and bent sideways as the crank swings. Because the load reverses, cracks begin at the transition from the shank to the big end.
That is why rods are shot peened and why the cap must stay with its original rod: each pair is machined together and cannot be swapped without losing bore alignment.
Rods are forged from alloy steel with controlled grain flow, shot peened and then machined. The big end bore and small end bush are finished to specification, and rods are weight matched within a set so the engine stays balanced.
A rod problem announces itself as noise. A deep knock that increases with load and speeds up with rpm is the classic sign of a worn big end bearing, and by that stage the rod is usually already damaged.
Check every rod for bend and twist before assembly, and verify the big end bore with new shells fitted and torqued. A rod that is out by only a little still fits, but it loads the piston against the bore and wears the bearing on one side.
Match the part number, the engine rating and the piston pin diameter. A rod from a different rating may be the wrong weight, which shows up as vibration and early main bearing wear. Compare the old rod with the new one at the small end before assembly.
The rod bearing is where most failures begin. Shells come in standard and undersize grades and the grade must match the journal after any regrind. Rod bolts are stretch bolts and must be replaced every time a rod is opened.
Detonation hammers the piston and rod on every cycle, squeezing the oil film out of the big end bearing until the shell fatigues. Engines that have run with a faulty injector, low fuel pressure or excessive boost often show rod bearing damage with no obvious wear elsewhere.
Rods are packed in a rigid carton with the big end protected and caps wired to their rods so they cannot be mixed in transit. If the shipment includes pistons, tell us so they can travel together and share freight.
Rod life depends on oil pressure and on avoiding detonation. Use the specified oil, change it at the severe-duty interval and never run with a leaking injector that dilutes the oil. Diagnose excessive smoke or power loss promptly rather than waiting for the next service.
Compare the small end bush and the old rod number, or send us photos.
New rod bolts are supplied where the design uses stretch bolts.
Yes, if the crank and other rods are undamaged. Match the weight class.
Mount on a surface plate with pins in both ends and measure with a dial gauge.
Browse the Weichai piston and components category, and pair the rod with the WP7 and WP8 connecting rod 610800030073 or the WP7 and WP8 piston 610800030035.
Weichai WP7 Connecting Rod (610800030040). The connecting rod transfers the firing impulse from the piston to the crankshaft. Its big end carries the highest alternating load of any bearing in the engine.
Note the rod bolt type and length. Bolts are torque-to-yield on these engines and must be new on every rebuild, so order them with the rod.
Numbers beginning 6108 belong to the WP7 and WP8 families. These engines share architecture but differ in detail, so a part that fits one will not necessarily suit the other without checking the casting. On this engine, confirm the WP7 application against the engine plate before ordering.
Use new rod bolts. A stretched bolt loses clamping load and the cap frets under load, which destroys the bearing and then the journal in quick succession.
Ordering note. Payment terms and shipping method are confirmed in writing before dispatch, including the port of loading and the estimated transit time.
Related reading: Piston Ring Selection: Gap, Tension and Bore Condition
| We Are 30 Years Diesel Engine Parts Supplier | |
| Brand | EPID |
| Warranty | 12 Months |
| Condition | 100%New |
| More Models | Weichai: WP7, WP7H, WP8, WP8H, and other Weichai series. |
| Shipping | By sea / air / express (DHL, FEDEX, TNT, UPS, EMS) |
| Packing | Standard exporting packing or as required |
| Payment Term | L/C, T/T, Western Union, Trade Assurance |
| Delivery Time | 3-7 days (depend on order) |
| Selling Point | 1. On-time Delivery 2. Genuine Quality Assurance 3. Professional Supplier |
Rods are forged from alloy steel with controlled grain flow, shot peened and then machined. The big end bore and small end bush are finished to specification, and rods are weight matched within a set so the engine stays balanced.
A rod problem announces itself as noise. A deep knock that increases with load and speeds up with rpm is the classic sign of a worn big end bearing, and by that stage the rod is usually already damaged.
Check every rod for bend and twist before assembly, and verify the big end bore with new shells fitted and torqued. A rod that is out by only a little still fits, but it loads the piston against the bore and wears the bearing on one side.
Match the part number, the engine rating and the piston pin diameter. A rod from a different rating may be the wrong weight, which shows up as vibration and early main bearing wear. Compare the old rod with the new one at the small end before assembly.
The rod bearing is where most failures begin. Shells come in standard and undersize grades and the grade must match the journal after any regrind. Rod bolts are stretch bolts and must be replaced every time a rod is opened.
Detonation hammers the piston and rod on every cycle, squeezing the oil film out of the big end bearing until the shell fatigues. Engines that have run with a faulty injector, low fuel pressure or excessive boost often show rod bearing damage with no obvious wear elsewhere.
Rods are packed in a rigid carton with the big end protected and caps wired to their rods so they cannot be mixed in transit. If the shipment includes pistons, tell us so they can travel together and share freight.
Rod life depends on oil pressure and on avoiding detonation. Use the specified oil, change it at the severe-duty interval and never run with a leaking injector that dilutes the oil. Diagnose excessive smoke or power loss promptly rather than waiting for the next service.
Browse the Weichai piston and components category, and pair the rod with the WP7 and WP8 connecting rod 610800030073 or the WP7 and WP8 piston 610800030035.


Compare the small end bush and the old rod number, or send us photos.
New rod bolts are supplied where the design uses stretch bolts.
Yes, if the crank and other rods are undamaged. Match the weight class.
Mount on a surface plate with pins in both ends and measure with a dial gauge.
EPID supplies diesel engine parts for Weichai, Baudouin, Yuchai, Caterpillar, Sinotruk, FAW Xichai and Cummins engines. Every order is checked against the original part number before packing, and our team can identify a part from a photo of the engine plate. Ask for a quotation with your model and quantity and we will reply within one working day.