< img height="1" width="1" style="display:none" src="https://www.facebook.com/tr?id=2042618782839916&ev=PageView&noscript=1" />
Diesel Engines & Parts
Weichai WD615 WP10 Oil Pump 612601080216 Diesel Engine Parts
Weichai WD615 WP10 Oil Pump 612601080216 Diesel Engine Parts

Weichai WD615 WP10 Oil Pump 612601080216 Diesel Engine Parts

Model: WD615 / WP10

Part Number: 612601080216

Brands: Weichai Power

Engine Model: WD615, WD615E2, WD10, WP10, WP10G

Engine Type: Diesel

Scope of application: heavy trucks, buses, construction machinery, generator sets

A pump number in the 612601 sequence

Weichai uses a long numeric sequence for oil pumps in this family, and 612601080216 is one of them. The differences between adjacent numbers are usually small in appearance but significant in fit: drive gear, pick-up and relief valve setting all vary between production batches. Confirm the engine plate and the old pump number, and check the front cover if it has been replaced.

What the pump must deliver

The pump feeds main and rod bearings, the camshaft, the valve train and the piston cooling jets. It must deliver volume at hot idle and hold pressure at rated speed without exceeding the relief valve setting. Wear shows first as a pressure drop at hot idle, not as a loss of peak pressure.

Bench testing before packing

  • Flow at rated speed compared with the original curve.
  • Relief valve opening pressure set and recorded.
  • Gear backlash and end clearance measured.
  • Leak test on the housing and pick-up joint.

Symptoms of pump wear

Low pressure at hot idle after a climb is the classic sign, and it is easy to dismiss because pressure returns as soon as engine speed rises. That recovery is exactly what tests the pump: a healthy pump holds pressure even when the oil is thinnest.

  • Warning light at hot idle
  • Pressure falling faster than engine speed
  • Filter bypass opening early
  • Metal debris in the filter
  • Worn gear teeth visible with the cover off
  • Oil weeping from the housing joint

Troubleshooting order

Check oil level and condition, replace the filter, inspect the strainer, then measure pressure with a mechanical gauge. Only after those steps should the pump come under suspicion, because a blocked strainer and a faulty sender both imitate a worn pump exactly.

Fitting and priming

  1. Clean the sump and strainer before fitting the pump.
  2. Inspect the drive gear and its mating gear.
  3. Fit new gaskets and O-rings and torque to specification.
  4. Prime the pump with clean oil and turn the engine by hand until oil reaches the head.
  5. Change oil and filter after the first start.
  6. Verify pressure at idle and rated speed before returning the vehicle to service.

Piston cooling and flow

On these engines the pump also supplies the piston cooling jets, which is easy to forget when diagnosing pressure alone. A pump that holds pressure but has lost volume still allows crown temperatures to climb, and the damage appears as a scored piston rather than low oil pressure.

Choosing the correct pump

Match the part number, the engine rating and the drive type. Send a photo of the old pump beside a ruler and we will confirm the casting before shipping.

Contamination and pump life

Most premature failures come from contaminated oil. Use the specified grade, change it at the severe-duty interval and never run with a leaking injector that thins the oil with diesel.

Oil analysis

Regular oil analysis catches bearing wear before pressure starts to fall. Rising iron and lead indicate that the oil film is breaking down somewhere in the engine.

Why the front cover matters

A replacement front cover can change the pump mounting face and the drive gear position. If the cover has been changed, compare the old pump with the new one on the bench before fitting, because the difference is not visible once the cover is on.

When to replace rather than diagnose

On a high-hour engine, replacing the pump during the overhaul is cheaper than diagnosing it separately. The part costs little compared with opening the front cover twice.

Reading pressure at three points

Record cold idle, hot idle and rated speed rather than a single figure. A pump that holds rated pressure but drops sharply at hot idle usually has worn bearings downstream, while pressure that recovers instantly with engine speed points to the relief valve or pump clearances.

Oil cooler restriction

A restricted oil cooler raises oil temperature and reduces pressure at the bearings even when the pump is healthy. Check cooler flow during an overhaul, and pressure test the bundle if there is any sign of coolant in the oil.

FAQ

Is a gasket included?

Yes, the mounting gasket and O-ring are supplied.

Can low pressure come from something else?

Yes. A blocked strainer, stuck relief valve, worn bearings or a faulty sender all mimic pump failure.

Is the drive gear supplied?

The pump comes with its drive gear fitted and timed as original.

When should the pump be replaced?

At every major overhaul, or whenever the front cover is removed.

Related parts and categories

Browse the Weichai pump category, and pair the pump with the WD615 oil pump 1000550425 or the WD615 crankshaft 612600020043.

Description

Weichai WD615 Oil Pump (612601080216). The oil pump moves a fixed volume per revolution. Pressure is created by the resistance that volume meets in the galleries and bearings, not by the pump alone.

Confirm the drive gear and pick-up match your front cover and sump. Adjacent part numbers frequently share a housing casting while differing in drive detail.

Numbers beginning 6126 belong to the generation shared with the WD618 and early WP12 engines. Parts in this block were revised several times, so the casting or housing is the reliable identifier rather than the number alone. On this engine, confirm the WD615 application against the engine plate before ordering.

Prime the pump before the first start and confirm oil pressure at the gauge before allowing the engine to run. Never crank a fresh rebuild hoping pressure will arrive.

Ordering note. Photographs of the actual unit can be sent before dispatch on request. That is the cheapest way to avoid a return when a casting revision is in doubt.

Related reading: Oil Pump Diagnosis: Low Pressure, Wear and Replacement

We Are 30 Years Diesel Engine Parts Supplier
BrandEPID
Warranty12 Months
Condition100%New
More ModelsWeichai: WD615, WD615E2, WD10, WP10, WP10G, and other Weichai series.
ShippingBy sea / air / express (DHL, FEDEX, TNT, UPS, EMS)
PackingStandard exporting packing or as required
Payment TermL/C, T/T, Western Union, Trade Assurance
Delivery Time3-7 days (depend on order)
Selling Point1. On-time Delivery   2. Genuine Quality Assurance   3. Professional Supplier

Bench testing before packing

  • Flow at rated speed compared with the original curve.
  • Relief valve opening pressure set and recorded.
  • Gear backlash and end clearance measured.
  • Leak test on the housing and pick-up joint.

Symptoms of pump wear

Low pressure at hot idle after a climb is the classic sign, and it is easy to dismiss because pressure returns as soon as engine speed rises. That recovery is exactly what tests the pump: a healthy pump holds pressure even when the oil is thinnest.

  • Warning light at hot idle
  • Pressure falling faster than engine speed
  • Filter bypass opening early
  • Metal debris in the filter
  • Worn gear teeth visible with the cover off
  • Oil weeping from the housing joint

Troubleshooting order

Check oil level and condition, replace the filter, inspect the strainer, then measure pressure with a mechanical gauge. Only after those steps should the pump come under suspicion, because a blocked strainer and a faulty sender both imitate a worn pump exactly.

Fitting and priming

  1. Clean the sump and strainer before fitting the pump.
  2. Inspect the drive gear and its mating gear.
  3. Fit new gaskets and O-rings and torque to specification.
  4. Prime the pump with clean oil and turn the engine by hand until oil reaches the head.
  5. Change oil and filter after the first start.
  6. Verify pressure at idle and rated speed before returning the vehicle to service.

Piston cooling and flow

On these engines the pump also supplies the piston cooling jets, which is easy to forget when diagnosing pressure alone. A pump that holds pressure but has lost volume still allows crown temperatures to climb, and the damage appears as a scored piston rather than low oil pressure.

Choosing the correct pump

Match the part number, the engine rating and the drive type. Send a photo of the old pump beside a ruler and we will confirm the casting before shipping.

Contamination and pump life

Most premature failures come from contaminated oil. Use the specified grade, change it at the severe-duty interval and never run with a leaking injector that thins the oil with diesel.

Oil analysis

Regular oil analysis catches bearing wear before pressure starts to fall. Rising iron and lead indicate that the oil film is breaking down somewhere in the engine.

Why the front cover matters

A replacement front cover can change the pump mounting face and the drive gear position. If the cover has been changed, compare the old pump with the new one on the bench before fitting, because the difference is not visible once the cover is on.

When to replace rather than diagnose

On a high-hour engine, replacing the pump during the overhaul is cheaper than diagnosing it separately. The part costs little compared with opening the front cover twice.

Reading pressure at three points

Record cold idle, hot idle and rated speed rather than a single figure. A pump that holds rated pressure but drops sharply at hot idle usually has worn bearings downstream, while pressure that recovers instantly with engine speed points to the relief valve or pump clearances.

Oil cooler restriction

A restricted oil cooler raises oil temperature and reduces pressure at the bearings even when the pump is healthy. Check cooler flow during an overhaul, and pressure test the bundle if there is any sign of coolant in the oil.

Related parts and categories

Browse the Weichai pump category, and pair the pump with the WD615 oil pump 1000550425 or the WD615 crankshaft 612600020043.

Detailed picture

Weichai WD615 WP10 Oil Pump 612601080216 Diesel Engine Parts
Weichai WD615 WP10 Oil Pump 612601080216 Diesel Engine Parts

Q&A

  • Is a gasket included?

    Yes, the mounting gasket and O-ring are supplied.

  • Can low pressure come from something else?

    Yes. A blocked strainer, stuck relief valve, worn bearings or a faulty sender all mimic pump failure.

  • Is the drive gear supplied?

    The pump comes with its drive gear fitted and timed as original.

  • When should the pump be replaced?

    At every major overhaul, or whenever the front cover is removed.

Why buy from EPID

EPID supplies diesel engine parts for Weichai, Baudouin, Yuchai, Caterpillar, Sinotruk, FAW Xichai and Cummins engines. Every order is checked against the original part number before packing, and our team can identify a part from a photo of the engine plate. Ask for a quotation with your model and quantity and we will reply within one working day.

send message

    • [recaptcha]

    Home Tel Mail Inquiry