

Model: WD615 / WP10
Part Number: 612600020043
Brands: Weichai Power
Engine Model: WD615, WD615E2, WD10, WP10, WP10G
Engine Type: Diesel
Scope of application: heavy trucks, buses, construction machinery, generator sets
Weichai WD615 crankshafts appear under both 6126 and 1006 number prefixes, and 612600020043 belongs to the first group. The differences between shafts in the family are usually in the damper fixing or the flywheel flange rather than in journal dimensions, so a shaft can fit the block and still not accept your existing damper.
These six-cylinder engines work at high load, so the shaft sees strong bending and torsional pulses. It carries the main and rod bearings, drives the oil pump and camshaft through the gear train and delivers torque to the flywheel. Once a journal loses roundness the bearing cannot maintain an oil film and failure follows quickly.
Bearing noise and oil pressure are the indicators that matter, and the knock appears later than the pressure change. By the time the knock is audible the journal is already damaged.
Match the part number, the journal size and the shells you intend to fit. Photographs of both shaft ends resolve the variant question faster than any catalogue. Send the bearing part numbers as well and we will confirm the journal size before shipping.
When the damper rubber perishes, torsional oscillation reaches the shaft and cracks begin at the fillets. Many failures blamed on lubrication are actually damper failures. Inspect the damper whenever the shaft is out and replace it with the new shaft.
The rear main bearing is fed by a gallery crossing the block. If that gallery is left partially blocked after cleaning, the rear bearing runs dry first and the shaft shows heat marks exactly there. The rear seal also runs on the flange, so a scored surface will leak even with a new seal.
Shafts are bolted into braced crates with journals sleeved and lifting points marked. Tell us whether the shaft travels with a block so we can plan the load and reduce cost.
Lubrication and vibration control decide crankshaft life. Use the specified oil, change it at the severe-duty interval and never run with a leaking injector that dilutes the oil.
Manufacturers revise crankshafts for a stronger damper, a different flywheel pattern or a supplier change. Two shafts can measure identically at the journals and still not be interchangeable, so comparing both ends matters as much as checking the number. A photograph of each end beside the old shaft is the quickest confirmation.
Shells come in standard and undersize grades, and the grade must match the journal after any regrind. Check clearance with plastigauge at every journal and record the figures for the rebuild log.
A lightly scored journal can be polished and a worn shaft reground to an undersize where shells exist in that grade. Each grinding pass removes hardened layer, so a shaft that has been through two grinds has little fatigue margin left. For heavy haulage, that margin matters more than the saving.
The flange carries full engine torque into the gearbox. A worn or corroded face causes clutch or converter problems that look unrelated to the crankshaft, so inspect it on arrival and protect it during installation.
The rear main bearing is fed by a gallery crossing the block. If that gallery is left partially blocked after cleaning, the rear bearing runs dry first and the shaft shows heat marks exactly there. The rear seal also runs on the shaft flange, so a scored surface will leak even with a new seal, and the leak is often blamed on the seal itself.
Record journal diameters, ovality and clearances in the engine log. The next overhaul then compares wear rates rather than starting from zero, and any warranty discussion is easier with figures on file.
Yes, journals and fillets are nitrided.
Only if enough hardened layer remains.
Strongly recommended with a new shaft.
Mount on centres and measure run-out.
Explore the Weichai crankshaft category, and complete the bottom end with the WD615 crankshaft 1006466588 or the WD615 oil pump 1000550425.
Weichai WD615 Crankshaft (612600020043). The crankshaft converts combustion pressure into torque and carries the entire load of the rotating assembly. Its journals set the oil film that keeps the bearings alive.
Measure ovality at several positions along each journal, not at one point. A journal can read the correct diameter and still be oval by a few hundredths, which collapses the oil film twice per revolution.
Numbers beginning 6126 belong to the generation shared with the WD618 and early WP12 engines. Parts in this block were revised several times, so the casting or housing is the reliable identifier rather than the number alone. On this engine, confirm the WD615 application against the engine plate before ordering.
Ask the machine shop explicitly whether the fillet radius has been restored, and to what value. Fatigue cracks start at the journal-to-web transition, and a sharp corner from grinding is where they begin.
Ordering note. Lead time depends on whether the item is in stock or has to be produced; the position is confirmed before the order is accepted rather than after payment.
Related reading: Crankshaft Inspection: Journals, Fillets and Regrinding
| We Are 30 Years Diesel Engine Parts Supplier | |
| Brand | EPID |
| Warranty | 12 Months |
| Condition | 100%New |
| More Models | Weichai: WD615, WD615E2, WD10, WP10, WP10G, and other Weichai series. |
| Shipping | By sea / air / express (DHL, FEDEX, TNT, UPS, EMS) |
| Packing | Standard exporting packing or as required |
| Payment Term | L/C, T/T, Western Union, Trade Assurance |
| Delivery Time | 3-7 days (depend on order) |
| Selling Point | 1. On-time Delivery 2. Genuine Quality Assurance 3. Professional Supplier |
Bearing noise and oil pressure are the indicators that matter, and the knock appears later than the pressure change. By the time the knock is audible the journal is already damaged.
Match the part number, the journal size and the shells you intend to fit. Photographs of both shaft ends resolve the variant question faster than any catalogue. Send the bearing part numbers as well and we will confirm the journal size before shipping.
When the damper rubber perishes, torsional oscillation reaches the shaft and cracks begin at the fillets. Many failures blamed on lubrication are actually damper failures. Inspect the damper whenever the shaft is out and replace it with the new shaft.
The rear main bearing is fed by a gallery crossing the block. If that gallery is left partially blocked after cleaning, the rear bearing runs dry first and the shaft shows heat marks exactly there. The rear seal also runs on the flange, so a scored surface will leak even with a new seal.
Shafts are bolted into braced crates with journals sleeved and lifting points marked. Tell us whether the shaft travels with a block so we can plan the load and reduce cost.
Lubrication and vibration control decide crankshaft life. Use the specified oil, change it at the severe-duty interval and never run with a leaking injector that dilutes the oil.
Manufacturers revise crankshafts for a stronger damper, a different flywheel pattern or a supplier change. Two shafts can measure identically at the journals and still not be interchangeable, so comparing both ends matters as much as checking the number. A photograph of each end beside the old shaft is the quickest confirmation.
Shells come in standard and undersize grades, and the grade must match the journal after any regrind. Check clearance with plastigauge at every journal and record the figures for the rebuild log.
A lightly scored journal can be polished and a worn shaft reground to an undersize where shells exist in that grade. Each grinding pass removes hardened layer, so a shaft that has been through two grinds has little fatigue margin left. For heavy haulage, that margin matters more than the saving.
The flange carries full engine torque into the gearbox. A worn or corroded face causes clutch or converter problems that look unrelated to the crankshaft, so inspect it on arrival and protect it during installation.
The rear main bearing is fed by a gallery crossing the block. If that gallery is left partially blocked after cleaning, the rear bearing runs dry first and the shaft shows heat marks exactly there. The rear seal also runs on the shaft flange, so a scored surface will leak even with a new seal, and the leak is often blamed on the seal itself.
Record journal diameters, ovality and clearances in the engine log. The next overhaul then compares wear rates rather than starting from zero, and any warranty discussion is easier with figures on file.
Explore the Weichai crankshaft category, and complete the bottom end with the WD615 crankshaft 1006466588 or the WD615 oil pump 1000550425.


Yes, journals and fillets are nitrided.
Only if enough hardened layer remains.
Strongly recommended with a new shaft.
Mount on centres and measure run-out.
EPID supplies diesel engine parts for Weichai, Baudouin, Yuchai, Caterpillar, Sinotruk, FAW Xichai and Cummins engines. Every order is checked against the original part number before packing, and our team can identify a part from a photo of the engine plate. Ask for a quotation with your model and quantity and we will reply within one working day.