< img height="1" width="1" style="display:none" src="https://www.facebook.com/tr?id=2042618782839916&ev=PageView&noscript=1" />
Diesel Engines & Parts
Baudouin 4M10G70 Full Gasket Kit 7000001981 Marine Diesel Parts
Baudouin 4M10G70 Full Gasket Kit 7000001981 Marine Diesel Parts
Baudouin 4M10G70 Full Gasket Kit 7000001981 Marine Diesel Parts

Baudouin 4M10G70 Full Gasket Kit 7000001981 Marine Diesel Parts

Model: 4M10G70

Part Number: 7000001981

Brands: Baudouin

Engine Model: 4M10G70

Engine Type: Marine and industrial diesel

Scope of application: marine propulsion, marine auxiliary, generator sets

What ships in kit 7000001981

This is the complete sealing set for a Baudouin 4M10G70 rebuild: head gasket, valve cover gasket, manifold gaskets, oil pan gasket, crank seals, pump and thermostat housing seals, injector copper washers and the small O-rings used across the engine.

The G70 is commonly used for auxiliary duty, driving generators on working boats. An auxiliary engine that leaks oil into the bilge or loses coolant at sea is a safety issue, which is why renewing every joint at once is worth the small extra cost.

Why the G70 kit is rating specific

The 4M10G70 shares many parts with the G88 and G110, but the head gasket is matched to its compression ratio and head casting. A higher-rated gasket set will fit but will not seal correctly at the G70's clamping load.

Materials and standards

  • Head gasket: multi-layer steel with correct fire ring and coolant holes.
  • Manifold gaskets: composite with a metal core.
  • Pan and cover gaskets: reinforced fibre.
  • Seals and washers: complete set checked against the parts list.

Symptoms of a failed gasket set

  • Oil weeping from the pan rail or rear main
  • Coolant seeping at the pump or thermostat housing
  • Soot marks around manifold joints
  • Bubbles in the heat exchanger
  • Oil and coolant mixing
  • Compression loss between adjacent cylinders

Installation notes

  1. Clean every mating surface to bare metal.
  2. Check head and block deck flatness.
  3. Fit the steel head gasket dry.
  4. Use new head bolts and torque in the factory sequence.
  5. Apply anaerobic sealant only where specified.
  6. Recheck for leaks after the first heat cycle.

Auxiliary engines and leak consequences

An auxiliary engine usually sits in a confined space where oil and coolant leaks collect unseen. A small weep that would be noticed on a truck goes unnoticed on a genset until the bilge alarm sounds. Renewing the full set at overhaul removes that risk.

Which gasket failed first

Identify the failure before opening the engine: a head gasket failure consumes coolant, a manifold failure leaves soot, a rear seal failure leaves oil at the bell housing. Knowing which failed tells you whether a full kit is needed.

Head bolts and clamping load

Head bolts are torque-to-yield and must be replaced every time. Reusing them is the most common reason a new gasket fails early, and the failure is usually blamed on the gasket.

Working safely on a marine engine

Never open a pressurised cooling system while hot. Let the engine cool completely, then release the cap slowly.

Storage and handling

Store flat, dry and out of sunlight. Composite gaskets absorb moisture slowly, so a kit stored in a damp engine room should be inspected before fitting.

Freight and consolidation

Kits are light and compact and consolidate well with liners or pistons. Tell us what else is in the shipment so the kit is packed on top.

Manifold gaskets and exhaust leaks

Manifold gaskets fail differently from head gaskets. The symptom is a ticking or whistling under load and soot tracks at the joint, not coolant loss. On a marine engine an exhaust leak into the engine room is a carbon monoxide risk, which makes this gasket more important than its price suggests.

Check the manifold face for warping when the gasket is replaced. A manifold that has been hot can bow, and a new gasket on a bowed face leaks again within weeks. Machining the face flat is a small job compared with a second strip-down.

Coolant passages in the gasket set

Some manifold gaskets also seal coolant passages. Check that the holes in the new gasket align with the passages in the manifold and head before fitting, because a gasket from a different rating can block a passage and cause a local hot spot.

Parts worth replacing while the engine is open

When the gasket set is being fitted, consider the thermostat, the water pump seal and the injector copper washers. These are inexpensive parts whose failure would mean opening the same joints again. On an auxiliary engine in a cramped space, the labour to reach those joints is far more than the parts cost.

Record what was replaced in the engine log, including part numbers. The next overhaul then starts with a clear picture instead of guesswork about what is inside the engine.

FAQ

Is the head gasket included?

Yes, this is a full set.

Does it fit G88 and G110 engines?

No. Ask us for the matching kit.

Do I need sealant with the head gasket?

No. The steel gasket is installed dry.

Are the gaskets reusable?

No. Gaskets and copper washers are single-use.

Related parts and categories

Browse the Baudouin gasket set category, and pair the kit with the 4M10G70 cylinder head 1004713403 or the 4M10G70 overhaul kit 1000156637.

Description

Baudouin 4M10G70 Full Gasket Kit (7000001981). The gasket set seals combustion, coolant and oil at every joint opened during a top-end repair. The head gasket inside it is the component that decides whether the job holds.

Compare the old head gasket with the new one for fire ring position, coolant hole pattern and thickness. A gasket from the wrong generation bolts up and leaks at the fire ring.

The part number is the reliable identifier here. Where the old number is unreadable, measure the component and compare it with the drawing rather than guessing from the engine model. On this engine, confirm the 4M10G70 application against the engine plate before ordering.

Install the head gasket dry unless the manual says otherwise. Sealant prevents composite and MLS gaskets from seating correctly.

Ordering note. If the old number has been superseded, the replacement number is quoted alongside the original so the purchasing file stays consistent.

Related reading: Head Gasket Failure Symptoms and How to Choose a Replacement

We Are 30 Years Diesel Engine Parts Supplier
BrandEPID
Warranty12 Months
Condition100%New
More ModelsWeichai: 4M10G70, and other Weichai series.
ShippingBy sea / air / express (DHL, FEDEX, TNT, UPS, EMS)
PackingStandard exporting packing or as required
Payment TermL/C, T/T, Western Union, Trade Assurance
Delivery Time3-7 days (depend on order)
Selling Point1. On-time Delivery   2. Genuine Quality Assurance   3. Professional Supplier

Materials and standards

  • Head gasket: multi-layer steel with correct fire ring and coolant holes.
  • Manifold gaskets: composite with a metal core.
  • Pan and cover gaskets: reinforced fibre.
  • Seals and washers: complete set checked against the parts list.

Symptoms of a failed gasket set

  • Oil weeping from the pan rail or rear main
  • Coolant seeping at the pump or thermostat housing
  • Soot marks around manifold joints
  • Bubbles in the heat exchanger
  • Oil and coolant mixing
  • Compression loss between adjacent cylinders

Installation notes

  1. Clean every mating surface to bare metal.
  2. Check head and block deck flatness.
  3. Fit the steel head gasket dry.
  4. Use new head bolts and torque in the factory sequence.
  5. Apply anaerobic sealant only where specified.
  6. Recheck for leaks after the first heat cycle.

Auxiliary engines and leak consequences

An auxiliary engine usually sits in a confined space where oil and coolant leaks collect unseen. A small weep that would be noticed on a truck goes unnoticed on a genset until the bilge alarm sounds. Renewing the full set at overhaul removes that risk.

Which gasket failed first

Identify the failure before opening the engine: a head gasket failure consumes coolant, a manifold failure leaves soot, a rear seal failure leaves oil at the bell housing. Knowing which failed tells you whether a full kit is needed.

Head bolts and clamping load

Head bolts are torque-to-yield and must be replaced every time. Reusing them is the most common reason a new gasket fails early, and the failure is usually blamed on the gasket.

Working safely on a marine engine

Never open a pressurised cooling system while hot. Let the engine cool completely, then release the cap slowly.

Storage and handling

Store flat, dry and out of sunlight. Composite gaskets absorb moisture slowly, so a kit stored in a damp engine room should be inspected before fitting.

Freight and consolidation

Kits are light and compact and consolidate well with liners or pistons. Tell us what else is in the shipment so the kit is packed on top.

Manifold gaskets and exhaust leaks

Manifold gaskets fail differently from head gaskets. The symptom is a ticking or whistling under load and soot tracks at the joint, not coolant loss. On a marine engine an exhaust leak into the engine room is a carbon monoxide risk, which makes this gasket more important than its price suggests.

Check the manifold face for warping when the gasket is replaced. A manifold that has been hot can bow, and a new gasket on a bowed face leaks again within weeks. Machining the face flat is a small job compared with a second strip-down.

Coolant passages in the gasket set

Some manifold gaskets also seal coolant passages. Check that the holes in the new gasket align with the passages in the manifold and head before fitting, because a gasket from a different rating can block a passage and cause a local hot spot.

Parts worth replacing while the engine is open

When the gasket set is being fitted, consider the thermostat, the water pump seal and the injector copper washers. These are inexpensive parts whose failure would mean opening the same joints again. On an auxiliary engine in a cramped space, the labour to reach those joints is far more than the parts cost.

Record what was replaced in the engine log, including part numbers. The next overhaul then starts with a clear picture instead of guesswork about what is inside the engine.

Related parts and categories

Browse the Baudouin gasket set category, and pair the kit with the 4M10G70 cylinder head 1004713403 or the 4M10G70 overhaul kit 1000156637.

Detailed picture

Baudouin 4M10G70 Full Gasket Kit 7000001981 Marine Diesel Parts
Baudouin 4M10G70 Full Gasket Kit 7000001981 Marine Diesel Parts
Baudouin 4M10G70 Full Gasket Kit 7000001981 Marine Diesel Parts

Q&A

  • Is the head gasket included?

    Yes, this is a full set.

  • Does it fit G88 and G110 engines?

    No. Ask us for the matching kit.

  • Do I need sealant with the head gasket?

    No. The steel gasket is installed dry.

  • Are the gaskets reusable?

    No. Gaskets and copper washers are single-use.

Why buy from EPID

EPID supplies diesel engine parts for Weichai, Baudouin, Yuchai, Caterpillar, Sinotruk, FAW Xichai and Cummins engines. Every order is checked against the original part number before packing, and our team can identify a part from a photo of the engine plate. Ask for a quotation with your model and quantity and we will reply within one working day.

send message

    • [recaptcha]

    Home Tel Mail Inquiry