< img height="1" width="1" style="display:none" src="https://www.facebook.com/tr?id=2042618782839916&ev=PageView&noscript=1" />
Diesel Engines & Parts
Baudouin 4M10G110 Full Gasket Kit 7000002541 Marine Diesel Parts
Baudouin 4M10G110 Full Gasket Kit 7000002541 Marine Diesel Parts
Baudouin 4M10G110 Full Gasket Kit 7000002541 Marine Diesel Parts
Baudouin 4M10G110 Full Gasket Kit 7000002541 Marine Diesel Parts

Baudouin 4M10G110 Full Gasket Kit 7000002541 Marine Diesel Parts

Model: 4M10G110

Part Number: 7000002541

Brands: Baudouin

Engine Model: 4M10G110

Engine Type: Marine and industrial diesel

Scope of application: marine propulsion, marine auxiliary, generator sets

Sealing the highest-rated 4M10G

The 4M10G110 runs at the highest combustion pressure in the Baudouin 4M10G family, so its sealing parts work harder than on the lower ratings. Kit 7000002541 contains the complete set: head gasket, valve cover gasket, manifold gaskets, oil pan gasket, crank seals, pump and thermostat housing seals, injector copper washers and the small O-rings.

On a boat, a leak is a safety issue as much as a maintenance one. Oil in the bilge is both a pollution and fire risk, and coolant loss at sea can stop the engine at the worst possible moment.

Why the G110 kit is different

The G110 shares many parts with the G70 and G88, but the head gasket is matched to its higher rating and to the coolant passage layout of its head casting. A gasket set from a lower rating will fit the block but will not seal correctly at full load.

Materials and standards

  • Head gasket: multi-layer steel with correct fire ring and coolant holes.
  • Manifold gaskets: composite with a metal core.
  • Pan and cover gaskets: reinforced fibre.
  • Seals and washers: complete set checked against the parts list.

Symptoms of a failed gasket set

  • Oil weeping from the pan rail or rear main
  • Coolant seeping at the pump or thermostat housing
  • Soot marks around manifold joints
  • Bubbles in the heat exchanger
  • Oil and coolant mixing
  • Compression loss between adjacent cylinders

Installation notes

  1. Clean every mating surface to bare metal.
  2. Check head and block deck flatness.
  3. Fit the steel head gasket dry.
  4. Use new head bolts and torque in the factory sequence.
  5. Apply anaerobic sealant only where specified.
  6. Recheck for leaks after the first heat cycle.

Head bolts and clamping load

The head gasket only seals if the clamping load is correct. Head bolts are torque-to-yield and must be replaced every time the head comes off. Reusing them is the single most common reason a new gasket fails within a few hundred hours, and the failure is usually blamed on the gasket.

Which gasket failed first

Identify the failure before opening the engine. A head gasket failure consumes coolant and pressurises the system. A manifold failure leaves soot tracks. A rear seal failure leaves oil at the bell housing. Knowing which one failed tells you whether a full kit is needed at all.

Working safely on a marine engine

Never open a pressurised cooling system while hot. The expansion tank on a boat can be above head height and releasing the cap can spray scalding coolant. Let the engine cool completely, then release slowly.

Storage and handling

Store flat, dry and out of sunlight. Composite gaskets absorb moisture slowly, and a kit stored in a damp engine room should be inspected before fitting. Keep the head gasket in its carton until the deck is ready.

Freight and consolidation

Kits are light and compact and consolidate well with liners or pistons. Tell us what else is in the shipment so the kit is packed on top.

Torque sequence and retorquing

The head gasket seals because the bolts clamp the head evenly. The factory sequence starts at the centre and works outward, which pushes the gasket out from the middle and avoids trapping air or coolant. Following a generic pattern instead is a reliable way to create a leak at one end of the head.

Retorquing after the first heat cycle is not required on modern torque-to-yield bolts, and doing it on a hot engine can actually reduce clamping force. Follow the manual rather than workshop habit.

Checking the deck before the gasket goes on

Measure flatness with a straight edge and feeler gauge along both diagonals and along the length. A deck that is out by more than the service limit must be machined, and no gasket will compensate for it. Record the measurement with the rebuild log.

Coolant loss at sea and how to diagnose it

On a marine engine, coolant loss is more serious than on a truck because there is no roadside recovery. If the level drops and there is no external trace, suspect the head gasket before anything else. A combustion gas test on the coolant takes minutes and gives a clear answer.

Keep a spare gasket set and a set of head bolts on board for long voyages. The parts are small, they do not deteriorate and they can turn a voyage-ending failure into a two-day repair at the next port.

FAQ

Is the head gasket included?

Yes, this is a full set with head gasket, manifold gaskets, pan gasket and crank seals.

Does it fit G70 and G88 engines?

No. Ask us for the matching kit.

Do I need sealant with the head gasket?

No. The steel gasket is installed dry.

Are the gaskets reusable?

No. Gaskets and copper washers are single-use.

Related parts and categories

Browse the Baudouin gasket set category, and pair the kit with the 4M10G110 cylinder head 1005045623 or the 4M10G110 overhaul kit 1005174218.

Description

Baudouin 4M10G110 Full Gasket Kit (7000002541). Sealing is the difference between a rebuild that finishes in one pass and one that waits a week for a missing washer. This set covers the head, manifolds, injectors and the small seals.

Compare the old head gasket with the new one for fire ring position, coolant hole pattern and thickness. A gasket from the wrong generation bolts up and leaks at the fire ring.

The part number is the reliable identifier here. Where the old number is unreadable, measure the component and compare it with the drawing rather than guessing from the engine model. On this engine, confirm the 4M10G110 application against the engine plate before ordering.

Use new head bolts and torque in three stages, then angle tighten in the factory sequence. Reused bolts reduce clamping load under load.

Ordering note. Payment terms and shipping method are confirmed in writing before dispatch, including the port of loading and the estimated transit time.

Related reading: Head Gasket Failure Symptoms and How to Choose a Replacement

We Are 30 Years Diesel Engine Parts Supplier
BrandEPID
Warranty12 Months
Condition100%New
More ModelsWeichai: 4M10G110, and other Weichai series.
ShippingBy sea / air / express (DHL, FEDEX, TNT, UPS, EMS)
PackingStandard exporting packing or as required
Payment TermL/C, T/T, Western Union, Trade Assurance
Delivery Time3-7 days (depend on order)
Selling Point1. On-time Delivery   2. Genuine Quality Assurance   3. Professional Supplier

Materials and standards

  • Head gasket: multi-layer steel with correct fire ring and coolant holes.
  • Manifold gaskets: composite with a metal core.
  • Pan and cover gaskets: reinforced fibre.
  • Seals and washers: complete set checked against the parts list.

Symptoms of a failed gasket set

  • Oil weeping from the pan rail or rear main
  • Coolant seeping at the pump or thermostat housing
  • Soot marks around manifold joints
  • Bubbles in the heat exchanger
  • Oil and coolant mixing
  • Compression loss between adjacent cylinders

Installation notes

  1. Clean every mating surface to bare metal.
  2. Check head and block deck flatness.
  3. Fit the steel head gasket dry.
  4. Use new head bolts and torque in the factory sequence.
  5. Apply anaerobic sealant only where specified.
  6. Recheck for leaks after the first heat cycle.

Head bolts and clamping load

The head gasket only seals if the clamping load is correct. Head bolts are torque-to-yield and must be replaced every time the head comes off. Reusing them is the single most common reason a new gasket fails within a few hundred hours, and the failure is usually blamed on the gasket.

Which gasket failed first

Identify the failure before opening the engine. A head gasket failure consumes coolant and pressurises the system. A manifold failure leaves soot tracks. A rear seal failure leaves oil at the bell housing. Knowing which one failed tells you whether a full kit is needed at all.

Working safely on a marine engine

Never open a pressurised cooling system while hot. The expansion tank on a boat can be above head height and releasing the cap can spray scalding coolant. Let the engine cool completely, then release slowly.

Storage and handling

Store flat, dry and out of sunlight. Composite gaskets absorb moisture slowly, and a kit stored in a damp engine room should be inspected before fitting. Keep the head gasket in its carton until the deck is ready.

Freight and consolidation

Kits are light and compact and consolidate well with liners or pistons. Tell us what else is in the shipment so the kit is packed on top.

Torque sequence and retorquing

The head gasket seals because the bolts clamp the head evenly. The factory sequence starts at the centre and works outward, which pushes the gasket out from the middle and avoids trapping air or coolant. Following a generic pattern instead is a reliable way to create a leak at one end of the head.

Retorquing after the first heat cycle is not required on modern torque-to-yield bolts, and doing it on a hot engine can actually reduce clamping force. Follow the manual rather than workshop habit.

Checking the deck before the gasket goes on

Measure flatness with a straight edge and feeler gauge along both diagonals and along the length. A deck that is out by more than the service limit must be machined, and no gasket will compensate for it. Record the measurement with the rebuild log.

Coolant loss at sea and how to diagnose it

On a marine engine, coolant loss is more serious than on a truck because there is no roadside recovery. If the level drops and there is no external trace, suspect the head gasket before anything else. A combustion gas test on the coolant takes minutes and gives a clear answer.

Keep a spare gasket set and a set of head bolts on board for long voyages. The parts are small, they do not deteriorate and they can turn a voyage-ending failure into a two-day repair at the next port.

Related parts and categories

Browse the Baudouin gasket set category, and pair the kit with the 4M10G110 cylinder head 1005045623 or the 4M10G110 overhaul kit 1005174218.

Detailed picture

Baudouin 4M10G110 Full Gasket Kit 7000002541 Marine Diesel Parts
Baudouin 4M10G110 Full Gasket Kit 7000002541 Marine Diesel Parts
Baudouin 4M10G110 Full Gasket Kit 7000002541 Marine Diesel Parts
Baudouin 4M10G110 Full Gasket Kit 7000002541 Marine Diesel Parts

Q&A

  • Is the head gasket included?

    Yes, this is a full set with head gasket, manifold gaskets, pan gasket and crank seals.

  • Does it fit G70 and G88 engines?

    No. Ask us for the matching kit.

  • Do I need sealant with the head gasket?

    No. The steel gasket is installed dry.

  • Are the gaskets reusable?

    No. Gaskets and copper washers are single-use.

Why buy from EPID

EPID supplies diesel engine parts for Weichai, Baudouin, Yuchai, Caterpillar, Sinotruk, FAW Xichai and Cummins engines. Every order is checked against the original part number before packing, and our team can identify a part from a photo of the engine plate. Ask for a quotation with your model and quantity and we will reply within one working day.

send message

    • [recaptcha]

    Home Tel Mail Inquiry