< img height="1" width="1" style="display:none" src="https://www.facebook.com/tr?id=2042618782839916&ev=PageView&noscript=1" />
Diesel Engines & Parts
Yuchai YC4108 Cylinder Head D30-D0300-1003010 Diesel Engine Parts
Yuchai YC4108 Cylinder Head D30-D0300-1003010 Diesel Engine Parts

Yuchai YC4108 Cylinder Head D30-D0300-1003010 Diesel Engine Parts

Model: YC4108

Part Number: D30-D0300-1003010

Brands: Yuchai

Engine Model: YC4108

Engine Type: Diesel

Scope of application: light and medium trucks, agricultural machinery, generator sets, marine auxiliary

A third head number for the YC4108

The YC4108 has carried several cylinder head castings over its production life, and part D30-D0300-1003010 is one of them. The differences between them are not cosmetic: injector bore depth, port shape and coolant passage layout changed between generations, and a head from the wrong generation fits the block but changes combustion.

That is why we ask for the old casting number and a photograph of the injector seat before shipping. A head that appears identical on the outside can behave very differently once the engine is running, and the fault usually appears as hard starting, smoke or a coolant leak at the rear of the head.

What the head does

The head closes the combustion chamber, carries the valve train and routes coolant around the injector and the valve bridges. It is where combustion pressure meets the cooling system, and the gasket between head and block has to seal both at once.

When a head warps or cracks, coolant enters the cylinder or compression enters the water jacket. Both produce symptoms that are easy to misread, which is why a pressure test and a combustion gas test should come before the engine is stripped.

Casting and machining checks

Each head is cast in high-grade iron, stress relieved and machined on the deck, valve seats, guides and injector bores. The checks that decide whether it will hold are all dimensional.

  • Deck flatness measured in both directions so the gasket seals evenly.
  • Valve seat width and concentricity, which control sealing and valve life.
  • Guide bore clearance, which controls oil consumption through the stems.
  • Injector bore depth and seat angle, so copper washers seal without blowing out.
  • Pressure test of the water jacket and exhaust ports above operating pressure.

Symptoms that point to the head

Head failures on the YC4108 usually begin with cooling. A restricted radiator or a tired water pump raises metal temperature, the deck warps and the gasket loses its grip. The early symptoms are easily mistaken for injector problems.

  • Coolant disappearing with no visible external leak
  • Bubbles in the radiator or coolant pushed out of the filler
  • White smoke that persists after warm-up
  • Coolant in the oil, visible as a milky dipstick
  • Compression loss on two adjacent cylinders
  • Overheating that returns after a thermostat replacement

Fitting the head

Preparation decides the outcome. Clean the block deck to bare metal, check flatness with a straight edge and a feeler gauge, and confirm that the head bolts are new before starting.

  1. Fit a new gasket dry, without sealant.
  2. Torque in three stages in the factory sequence, then angle tighten.
  3. Set valve clearance after the engine has run and cooled.
  4. Fill and bleed the cooling system with the specified mixture.
  5. Recheck injector clamp torque after the first hours of running.

Valve guides and oil consumption

Worn guides let oil down the stems, producing blue smoke at start-up that clears once the engine works. That pattern is often mistaken for worn rings, and the rebuild then goes in the wrong direction. Measuring guide clearance on the bench takes minutes and settles the question before parts are ordered.

Repair or replace

Light seat wear can be re-cut and a mildly warped deck machined once if enough material remains. Cracks between seats, at the injector bore or across the deck are not economically repairable, and a repaired head that fails again usually takes the gasket with it.

Cooling system care in the field

Field work packs the radiator core with chaff and dust, which raises coolant temperature regardless of pump condition. Clean the core with compressed air at every major service and confirm the fan and thermostat work. On a YC4108 in continuous field use, cooling neglect is the most common cause of head problems.

Head bolts and clamping load

Head bolts are torque-to-yield and must be replaced every time the head is removed. Reusing them reduces clamping force, and the gasket then leaks at high load. Order a new bolt set with every head rather than discovering the need halfway through assembly.

Choosing the correct head

Match the engine plate, the old casting number and the injector type. Send photographs of the old head and the nameplate and our team will confirm the variant before shipping, which is much cheaper than returning a head from an overseas port.

FAQ

Does the head come with valves?

Yes, unless a bare head is requested.

Can I reuse the head bolts?

No. They must be replaced every time.

How do I confirm a crack?

A pressure test and a combustion gas test confirm it.

Are heads interchangeable between YC4108 variants?

No. Confirm the casting number against the engine plate.

Related parts and categories

Browse the Yuchai cylinder head category, and pair the head with the YC4108 cylinder head D30-1003015A or the YC4108 full gasket kit D0300-1003001B.

Description

Yuchai YC4108 Cylinder Head (1003010). This casting closes the combustion chamber and carries the injector bores, the valve seats and the coolant passages. Its flatness and injector bore depth decide whether the engine runs cleanly or smokes.

Compare the old head gasket with the new one before the engine is stripped: fire ring position, coolant hole pattern and thickness. If any of the three differ, check the casting number against the engine plate.

Numbers beginning 1003 belong to the numeric series used across WP7, WP8 and WP9. The engine plate is the fastest way to confirm which revision applies. On this engine, confirm the YC4108 application against the engine plate before ordering.

Have the head checked for flatness and, where necessary, pressure tested before assembly. A crack that does not leak cold will open once the engine reaches temperature.

Ordering note. Lead time depends on whether the item is in stock or has to be produced; the position is confirmed before the order is accepted rather than after payment.

Related reading: Cylinder Head Rebuild: Valves, Guides and Seats

We Are 30 Years Diesel Engine Parts Supplier
BrandEPID
Warranty12 Months
Condition100%New
More ModelsWeichai: YC4108, and other Weichai series.
ShippingBy sea / air / express (DHL, FEDEX, TNT, UPS, EMS)
PackingStandard exporting packing or as required
Payment TermL/C, T/T, Western Union, Trade Assurance
Delivery Time3-7 days (depend on order)
Selling Point1. On-time Delivery   2. Genuine Quality Assurance   3. Professional Supplier

Casting and machining checks

Each head is cast in high-grade iron, stress relieved and machined on the deck, valve seats, guides and injector bores. The checks that decide whether it will hold are all dimensional.

  • Deck flatness measured in both directions so the gasket seals evenly.
  • Valve seat width and concentricity, which control sealing and valve life.
  • Guide bore clearance, which controls oil consumption through the stems.
  • Injector bore depth and seat angle, so copper washers seal without blowing out.
  • Pressure test of the water jacket and exhaust ports above operating pressure.

Symptoms that point to the head

Head failures on the YC4108 usually begin with cooling. A restricted radiator or a tired water pump raises metal temperature, the deck warps and the gasket loses its grip. The early symptoms are easily mistaken for injector problems.

  • Coolant disappearing with no visible external leak
  • Bubbles in the radiator or coolant pushed out of the filler
  • White smoke that persists after warm-up
  • Coolant in the oil, visible as a milky dipstick
  • Compression loss on two adjacent cylinders
  • Overheating that returns after a thermostat replacement

Fitting the head

Preparation decides the outcome. Clean the block deck to bare metal, check flatness with a straight edge and a feeler gauge, and confirm that the head bolts are new before starting.

  1. Fit a new gasket dry, without sealant.
  2. Torque in three stages in the factory sequence, then angle tighten.
  3. Set valve clearance after the engine has run and cooled.
  4. Fill and bleed the cooling system with the specified mixture.
  5. Recheck injector clamp torque after the first hours of running.

Valve guides and oil consumption

Worn guides let oil down the stems, producing blue smoke at start-up that clears once the engine works. That pattern is often mistaken for worn rings, and the rebuild then goes in the wrong direction. Measuring guide clearance on the bench takes minutes and settles the question before parts are ordered.

Repair or replace

Light seat wear can be re-cut and a mildly warped deck machined once if enough material remains. Cracks between seats, at the injector bore or across the deck are not economically repairable, and a repaired head that fails again usually takes the gasket with it.

Cooling system care in the field

Field work packs the radiator core with chaff and dust, which raises coolant temperature regardless of pump condition. Clean the core with compressed air at every major service and confirm the fan and thermostat work. On a YC4108 in continuous field use, cooling neglect is the most common cause of head problems.

Head bolts and clamping load

Head bolts are torque-to-yield and must be replaced every time the head is removed. Reusing them reduces clamping force, and the gasket then leaks at high load. Order a new bolt set with every head rather than discovering the need halfway through assembly.

Choosing the correct head

Match the engine plate, the old casting number and the injector type. Send photographs of the old head and the nameplate and our team will confirm the variant before shipping, which is much cheaper than returning a head from an overseas port.

Related parts and categories

Browse the Yuchai cylinder head category, and pair the head with the YC4108 cylinder head D30-1003015A or the YC4108 full gasket kit D0300-1003001B.

Detailed picture

Yuchai YC4108 Cylinder Head D30-D0300-1003010 Diesel Engine Parts
Yuchai YC4108 Cylinder Head D30-D0300-1003010 Diesel Engine Parts

Q&A

  • Does the head come with valves?

    Yes, unless a bare head is requested.

  • Can I reuse the head bolts?

    No. They must be replaced every time.

  • How do I confirm a crack?

    A pressure test and a combustion gas test confirm it.

  • Are heads interchangeable between YC4108 variants?

    No. Confirm the casting number against the engine plate.

Why buy from EPID

EPID supplies diesel engine parts for Weichai, Baudouin, Yuchai, Caterpillar, Sinotruk, FAW Xichai and Cummins engines. Every order is checked against the original part number before packing, and our team can identify a part from a photo of the engine plate. Ask for a quotation with your model and quantity and we will reply within one working day.

send message

    • [recaptcha]

    Home Tel Mail Inquiry