< img height="1" width="1" style="display:none" src="https://www.facebook.com/tr?id=2042618782839916&ev=PageView&noscript=1" />
Diesel Engines & Parts
Weichai WP7 WP8 Water Pump 610800060207 Diesel Engine Parts
Weichai WP7 WP8 Water Pump 610800060207 Diesel Engine Parts

Weichai WP7 WP8 Water Pump 610800060207 Diesel Engine Parts

Model: WP7 / WP8

Part Number: 610800060207

Brands: Weichai Power

Engine Model: WP7, WP7H, WP8, WP8H

Engine Type: Diesel

Scope of application: medium and heavy trucks, buses, construction machinery, generator sets

Pump numbers and pulley variants

Weichai lists several coolant pumps for the WP7 and WP8, and 610800060207 is one of them. The differences appear in the pulley diameter, the pulley offset and the inlet angle, which together decide whether the belt aligns and whether the hose reaches without strain. A pump with the correct casting and the wrong pulley fails within hours of fitting.

If the old pump has no readable number, measure the pulley diameter and the distance from the mounting face to the pulley centreline. Those figures identify the variant faster than any catalogue and can be taken with a ruler in a minute.

What the pump must do

The pump circulates coolant through the block, head, oil cooler and radiator at a rate matched to the heat produced under load. Because it runs at engine speed, its flow rises with rpm and the thermostat and radiator balance the system. A weak pump does not overheat the engine at idle; it overheats it under load, exactly when the truck is working hardest.

Construction and testing

The pump uses a cast iron housing, a cast impeller and a sealed bearing cartridge lubricated for life. Flow is tested at rated speed and the seal is tested above operating pressure, because neither can be judged by eye on the bench.

  • Impeller clearance set for efficient flow.
  • Bearing play measured at operating speed.
  • Seal integrity tested at pressure.
  • Flow test against the original curve.

Failure symptoms

The weep hole under the housing lets a failing seal drip visibly rather than contaminate the bearing. A small drip is a warning, and ignoring it until the bearing collapses turns a modest repair into an expensive one.

  • Weep from the drain hole or white crust
  • Rumbling or squealing from the front of the engine
  • Pulley or fan wobble
  • Overheating under load
  • Coolant smell after a run
  • Play in the pulley with the belt removed

Diagnosing overheating before replacing

Check coolant level and condition, confirm the thermostat opens, clean the radiator core, test the fan drive and inspect the belt for slip. A temperature difference between the radiator top and bottom hoses points to restricted flow through the core rather than a weak pump.

Installation and bleeding

Fit the pump to a clean surface with a new gasket, torque evenly and bleed the system completely. Trapped air creates local hot spots and can leave a new seal running dry at start-up.

  1. Drain coolant and dispose of it responsibly.
  2. Remove the belt and inspect the tensioner.
  3. Clean the block face and fit a new gasket.
  4. Torque bolts evenly in a cross pattern.
  5. Refill and bleed until the thermostat opens.
  6. Run to temperature, recheck level and look for weep.

Belt alignment and bearing life

Check the belt path with a straight edge across the pulleys and replace any tensioner or idler showing play. A side-loaded bearing fails quickly, and the failure is usually blamed on the pump rather than on the alignment that caused it.

Coolant quality and seal life

Use the specified coolant mixture and replace it at the recommended interval. Scale and contamination attack the seal faces, and plain water offers no protection, especially in hot climates or in dusty construction duty where the radiator core also loads up.

Choosing the correct pump

Match the engine plate, the old pump number and the pulley dimensions. Send a photo of the old pump beside a ruler and we will confirm the casting before shipping.

Stock planning

Pumps are compact and store well. Two on the shelf with gaskets and thermostat housing seals cover most fleet needs and avoid a long wait for a part that costs relatively little.

Thermostat and pressure cap

Replace both whenever the pump is replaced. A stuck thermostat makes the pump work against a closed circuit, and a weak cap lets coolant boil earlier. Both are inexpensive parts and both are frequently overlooked when a cooling problem is chased.

Why the pump body can look identical

Two pumps can share a housing casting and differ only in the pulley or the inlet elbow. That is why a photograph of the old pump beside a ruler, with the pulley visible, is more useful than a part number when the engine has been rebuilt or the accessories changed.

FAQ

Does the pump include a gasket?

Yes, the gasket and O-ring are supplied.

Can I drive with a weeping pump?

Only to reach a workshop.

Is the pulley included?

The pump comes with the hub.

How do I separate pump noise from belt noise?

Remove the belt and spin the pump by hand.

Related parts and categories

Browse the Weichai pump category, and pair the pump with the WP7 and WP8 water pump 610800060144 or the WP7 and WP8 oil pump 610800070312.

Description

Weichai WP7 Water Pump (610800060207). This pump maintains coolant velocity across the liners and through the head. Poor flow shows up as a temperature rise under load, not at idle.

Check the fan drive and thermostat before condemning the pump. A restricted radiator produces the same temperature rise under load and costs less to check.

Numbers beginning 6108 belong to the WP7 and WP8 families. These engines share architecture but differ in detail, so a part that fits one will not necessarily suit the other without checking the casting. On this engine, confirm the WP7 application against the engine plate before ordering.

Drain and refill with the correct coolant mix and bleed the system completely. Air in the system causes hot spots and accelerates cavitation damage on the liners.

Ordering note. Packing is export grade: each unit is wrapped, boxed and palletised for sea freight, with the part number marked on the outside so the receiving store can book it in without opening the carton.

Related reading: Cylinder Liner Cavitation: Causes, Symptoms and Prevention

We Are 30 Years Diesel Engine Parts Supplier
BrandEPID
Warranty12 Months
Condition100%New
More ModelsWeichai: WP7, WP7H, WP8, WP8H, and other Weichai series.
ShippingBy sea / air / express (DHL, FEDEX, TNT, UPS, EMS)
PackingStandard exporting packing or as required
Payment TermL/C, T/T, Western Union, Trade Assurance
Delivery Time3-7 days (depend on order)
Selling Point1. On-time Delivery   2. Genuine Quality Assurance   3. Professional Supplier

Construction and testing

The pump uses a cast iron housing, a cast impeller and a sealed bearing cartridge lubricated for life. Flow is tested at rated speed and the seal is tested above operating pressure, because neither can be judged by eye on the bench.

  • Impeller clearance set for efficient flow.
  • Bearing play measured at operating speed.
  • Seal integrity tested at pressure.
  • Flow test against the original curve.

Failure symptoms

The weep hole under the housing lets a failing seal drip visibly rather than contaminate the bearing. A small drip is a warning, and ignoring it until the bearing collapses turns a modest repair into an expensive one.

  • Weep from the drain hole or white crust
  • Rumbling or squealing from the front of the engine
  • Pulley or fan wobble
  • Overheating under load
  • Coolant smell after a run
  • Play in the pulley with the belt removed

Diagnosing overheating before replacing

Check coolant level and condition, confirm the thermostat opens, clean the radiator core, test the fan drive and inspect the belt for slip. A temperature difference between the radiator top and bottom hoses points to restricted flow through the core rather than a weak pump.

Installation and bleeding

Fit the pump to a clean surface with a new gasket, torque evenly and bleed the system completely. Trapped air creates local hot spots and can leave a new seal running dry at start-up.

  1. Drain coolant and dispose of it responsibly.
  2. Remove the belt and inspect the tensioner.
  3. Clean the block face and fit a new gasket.
  4. Torque bolts evenly in a cross pattern.
  5. Refill and bleed until the thermostat opens.
  6. Run to temperature, recheck level and look for weep.

Belt alignment and bearing life

Check the belt path with a straight edge across the pulleys and replace any tensioner or idler showing play. A side-loaded bearing fails quickly, and the failure is usually blamed on the pump rather than on the alignment that caused it.

Coolant quality and seal life

Use the specified coolant mixture and replace it at the recommended interval. Scale and contamination attack the seal faces, and plain water offers no protection, especially in hot climates or in dusty construction duty where the radiator core also loads up.

Choosing the correct pump

Match the engine plate, the old pump number and the pulley dimensions. Send a photo of the old pump beside a ruler and we will confirm the casting before shipping.

Stock planning

Pumps are compact and store well. Two on the shelf with gaskets and thermostat housing seals cover most fleet needs and avoid a long wait for a part that costs relatively little.

Thermostat and pressure cap

Replace both whenever the pump is replaced. A stuck thermostat makes the pump work against a closed circuit, and a weak cap lets coolant boil earlier. Both are inexpensive parts and both are frequently overlooked when a cooling problem is chased.

Why the pump body can look identical

Two pumps can share a housing casting and differ only in the pulley or the inlet elbow. That is why a photograph of the old pump beside a ruler, with the pulley visible, is more useful than a part number when the engine has been rebuilt or the accessories changed.

Related parts and categories

Browse the Weichai pump category, and pair the pump with the WP7 and WP8 water pump 610800060144 or the WP7 and WP8 oil pump 610800070312.

Detailed picture

Weichai WP7 WP8 Water Pump 610800060207 Diesel Engine Parts
Weichai WP7 WP8 Water Pump 610800060207 Diesel Engine Parts

Q&A

  • Does the pump include a gasket?

    Yes, the gasket and O-ring are supplied.

  • Can I drive with a weeping pump?

    Only to reach a workshop.

  • Is the pulley included?

    The pump comes with the hub.

  • How do I separate pump noise from belt noise?

    Remove the belt and spin the pump by hand.

Why buy from EPID

EPID supplies diesel engine parts for Weichai, Baudouin, Yuchai, Caterpillar, Sinotruk, FAW Xichai and Cummins engines. Every order is checked against the original part number before packing, and our team can identify a part from a photo of the engine plate. Ask for a quotation with your model and quantity and we will reply within one working day.

send message

    • [recaptcha]

    Home Tel Mail Inquiry