< img height="1" width="1" style="display:none" src="https://www.facebook.com/tr?id=2042618782839916&ev=PageView&noscript=1" />
Diesel Engines & Parts
Weichai WP7 WP8 Water Pump 610800060144 Diesel Engine Parts
Weichai WP7 WP8 Water Pump 610800060144 Diesel Engine Parts

Weichai WP7 WP8 Water Pump 610800060144 Diesel Engine Parts

Model: WP7 / WP8

Part Number: 610800060144

Brands: Weichai Power

Engine Model: WP7, WP7H, WP8, WP8H

Engine Type: Diesel

Scope of application: medium and heavy trucks, buses, construction machinery, generator sets

A pump number in the 610800 series

Weichai WP7 and WP8 coolant pumps appear under several numbers, and 610800060144 belongs to the 610800 series. The pumps differ mainly in pulley diameter and inlet angle, which decide whether the belt lines up and whether the hose reaches without strain. A correct pump with the wrong pulley destroys belt alignment on the first run.

When the old pump has no readable marking, measure the pulley diameter and the distance from the mounting face to the pulley centreline. Those two figures identify the variant faster than any catalogue and can be taken with a ruler on the bench in a minute.

What the pump has to do

The pump circulates coolant through the block, head, oil cooler and radiator at a rate matched to the heat produced under load. Because it runs at engine speed, its flow rises and falls with rpm, and the thermostat and radiator balance the system around it. When the pump loses efficiency, the engine does not overheat at idle; it overheats under load.

Construction and bench testing

The pump uses a cast iron housing, a cast impeller and a sealed bearing cartridge lubricated for life. Each unit is bench tested for flow at rated speed and for seal integrity above operating pressure, because neither can be judged by eye.

  • Impeller clearance set for efficient flow.
  • Bearing play measured at operating speed.
  • Seal integrity tested at pressure.
  • Flow test against the original curve.

Failure symptoms

The weep hole under the housing lets a failing seal drip where it can be seen rather than contaminating the bearing. A small drip is a warning, not something to ignore until the bearing collapses and the fan contacts the radiator.

  • Weep from the drain hole or white crust
  • Rumbling or squealing from the front of the engine
  • Pulley or fan wobble
  • Overheating under load
  • Coolant smell after a run
  • Play in the pulley with the belt removed

Diagnosing overheating before replacing

Check coolant level and condition, confirm the thermostat opens, clean the radiator core, test the fan drive and inspect the belt for slip. A useful field test is to feel the radiator top and bottom hoses once warm: a large difference points to restricted flow through the core rather than a weak pump, and cleaning the core solves the problem without parts.

Installation and bleeding

Fit the pump to a clean surface with a new gasket, torque evenly and bleed the system completely. Trapped air creates local hot spots and can leave a new seal running dry for the first seconds after start-up.

  1. Drain coolant and dispose of it responsibly.
  2. Remove the belt and inspect the tensioner.
  3. Clean the block face and fit a new gasket.
  4. Torque bolts evenly in a cross pattern.
  5. Refill and bleed until the thermostat opens.
  6. Run to temperature, recheck level and look for weep.

Belt alignment and bearing life

Check the belt path with a straight edge across the pulleys before fitting the pump, and replace any tensioner or idler showing play. A side-loaded bearing fails quickly, and the failure is usually blamed on the pump rather than on the alignment that caused it.

Coolant quality

Use the specified coolant mixture and replace it at the interval. Scale and contamination attack the seal faces, and plain water offers no protection at all, especially in engines working in hot climates or in dusty construction duty.

Choosing the correct pump

Match the engine plate, the old pump number and the pulley dimensions. Send a photo of the old pump beside a ruler and we will confirm the casting before shipping, which is cheaper than returning a pump that does not align.

Stock planning

Pumps are compact and store well. Two on the shelf with gaskets and thermostat housing seals cover most fleet needs and avoid a long wait for a part that costs relatively little.

Why the pump is only one link in the cooling chain

A blocked radiator core, a thermostat that opens late and a fan that no longer locks up all produce the same overheating pattern as a weak pump. Replacing the pump without checking those parts is the most common wasted repair on these engines. Keep the old pump after replacement and look at the seal and bearing: if both are intact, the fault was elsewhere.

Reading the weep hole correctly

A small weep is a seal warning; a steady drip with the engine cold means the seal has already failed. Distinguishing the two prevents replacing a serviceable pump while still catching a failure before the bearing is destroyed.

FAQ

Does the pump include a gasket?

Yes, the gasket and O-ring are supplied.

Can I drive with a weeping pump?

Only to reach a workshop.

Is the pulley included?

The pump comes with the hub.

How do I separate pump noise from belt noise?

Remove the belt and spin the pump by hand.

Related parts and categories

Browse the Weichai pump category, and pair the pump with the WP7 and WP8 water pump 1002372182 or the WP7 and WP8 full gasket kit 1001514985.

Description

Weichai WP7 Water Pump (610800060144). This pump maintains coolant velocity across the liners and through the head. Poor flow shows up as a temperature rise under load, not at idle.

Check the fan drive and thermostat before condemning the pump. A restricted radiator produces the same temperature rise under load and costs less to check.

Numbers beginning 6108 belong to the WP7 and WP8 families. These engines share architecture but differ in detail, so a part that fits one will not necessarily suit the other without checking the casting. On this engine, confirm the WP7 application against the engine plate before ordering.

Drain and refill with the correct coolant mix and bleed the system completely. Air in the system causes hot spots and accelerates cavitation damage on the liners.

Ordering note. Mixed pallets are accepted, so a single order can carry the block, the gasket set and the small seals together instead of arriving in three shipments.

Related reading: Cylinder Liner Cavitation: Causes, Symptoms and Prevention

We Are 30 Years Diesel Engine Parts Supplier
BrandEPID
Warranty12 Months
Condition100%New
More ModelsWeichai: WP7, WP7H, WP8, WP8H, and other Weichai series.
ShippingBy sea / air / express (DHL, FEDEX, TNT, UPS, EMS)
PackingStandard exporting packing or as required
Payment TermL/C, T/T, Western Union, Trade Assurance
Delivery Time3-7 days (depend on order)
Selling Point1. On-time Delivery   2. Genuine Quality Assurance   3. Professional Supplier

Construction and bench testing

The pump uses a cast iron housing, a cast impeller and a sealed bearing cartridge lubricated for life. Each unit is bench tested for flow at rated speed and for seal integrity above operating pressure, because neither can be judged by eye.

  • Impeller clearance set for efficient flow.
  • Bearing play measured at operating speed.
  • Seal integrity tested at pressure.
  • Flow test against the original curve.

Failure symptoms

The weep hole under the housing lets a failing seal drip where it can be seen rather than contaminating the bearing. A small drip is a warning, not something to ignore until the bearing collapses and the fan contacts the radiator.

  • Weep from the drain hole or white crust
  • Rumbling or squealing from the front of the engine
  • Pulley or fan wobble
  • Overheating under load
  • Coolant smell after a run
  • Play in the pulley with the belt removed

Diagnosing overheating before replacing

Check coolant level and condition, confirm the thermostat opens, clean the radiator core, test the fan drive and inspect the belt for slip. A useful field test is to feel the radiator top and bottom hoses once warm: a large difference points to restricted flow through the core rather than a weak pump, and cleaning the core solves the problem without parts.

Installation and bleeding

Fit the pump to a clean surface with a new gasket, torque evenly and bleed the system completely. Trapped air creates local hot spots and can leave a new seal running dry for the first seconds after start-up.

  1. Drain coolant and dispose of it responsibly.
  2. Remove the belt and inspect the tensioner.
  3. Clean the block face and fit a new gasket.
  4. Torque bolts evenly in a cross pattern.
  5. Refill and bleed until the thermostat opens.
  6. Run to temperature, recheck level and look for weep.

Belt alignment and bearing life

Check the belt path with a straight edge across the pulleys before fitting the pump, and replace any tensioner or idler showing play. A side-loaded bearing fails quickly, and the failure is usually blamed on the pump rather than on the alignment that caused it.

Coolant quality

Use the specified coolant mixture and replace it at the interval. Scale and contamination attack the seal faces, and plain water offers no protection at all, especially in engines working in hot climates or in dusty construction duty.

Choosing the correct pump

Match the engine plate, the old pump number and the pulley dimensions. Send a photo of the old pump beside a ruler and we will confirm the casting before shipping, which is cheaper than returning a pump that does not align.

Stock planning

Pumps are compact and store well. Two on the shelf with gaskets and thermostat housing seals cover most fleet needs and avoid a long wait for a part that costs relatively little.

Why the pump is only one link in the cooling chain

A blocked radiator core, a thermostat that opens late and a fan that no longer locks up all produce the same overheating pattern as a weak pump. Replacing the pump without checking those parts is the most common wasted repair on these engines. Keep the old pump after replacement and look at the seal and bearing: if both are intact, the fault was elsewhere.

Reading the weep hole correctly

A small weep is a seal warning; a steady drip with the engine cold means the seal has already failed. Distinguishing the two prevents replacing a serviceable pump while still catching a failure before the bearing is destroyed.

Related parts and categories

Browse the Weichai pump category, and pair the pump with the WP7 and WP8 water pump 1002372182 or the WP7 and WP8 full gasket kit 1001514985.

Detailed picture

Weichai WP7 WP8 Water Pump 610800060144 Diesel Engine Parts
Weichai WP7 WP8 Water Pump 610800060144 Diesel Engine Parts

Q&A

  • Does the pump include a gasket?

    Yes, the gasket and O-ring are supplied.

  • Can I drive with a weeping pump?

    Only to reach a workshop.

  • Is the pulley included?

    The pump comes with the hub.

  • How do I separate pump noise from belt noise?

    Remove the belt and spin the pump by hand.

Why buy from EPID

EPID supplies diesel engine parts for Weichai, Baudouin, Yuchai, Caterpillar, Sinotruk, FAW Xichai and Cummins engines. Every order is checked against the original part number before packing, and our team can identify a part from a photo of the engine plate. Ask for a quotation with your model and quantity and we will reply within one working day.

send message

    • [recaptcha]

    Home Tel Mail Inquiry