< img height="1" width="1" style="display:none" src="https://www.facebook.com/tr?id=2042618782839916&ev=PageView&noscript=1" />
Diesel Engines & Parts
Weichai WP7 WP8 Water Pump 1002372182 Diesel Engine Parts
Weichai WP7 WP8 Water Pump 1002372182 Diesel Engine Parts

Weichai WP7 WP8 Water Pump 1002372182 Diesel Engine Parts

Model: WP7 / WP8

Part Number: 1002372182

Brands: Weichai Power

Engine Model: WP7, WP7H, WP8, WP8H

Engine Type: Diesel

Scope of application: medium and heavy trucks, buses, construction machinery, generator sets

A coolant pump number in the WP7 and WP8 family

The WP7 and WP8 have used several coolant pump numbers, and 1002372182 is one of them. The differences appear in the pulley and inlet arrangement rather than in the pumping element, which means two pumps can look nearly identical and still not align with the belt.

Confirm the engine plate and the old pump number before ordering. If the old pump has no readable marking, measure the pulley diameter and the distance from the mounting face to the pulley centreline; those two figures identify the variant.

What the pump has to do

The pump circulates coolant through the block, head, oil cooler and radiator at a rate matched to the heat produced under load. Because it runs at engine speed, its flow rises and falls with rpm, and the thermostat and radiator balance the system around it.

When the pump loses efficiency, the engine does not overheat at idle. It overheats under load, which is the pattern that separates a weak pump from a blocked radiator core.

Construction and bench testing

The pump uses a cast iron housing, a precision cast impeller and a sealed bearing cartridge lubricated for life. The mechanical face seal is tested above operating pressure, and flow is measured at rated speed against the original curve.

  • Impeller clearance set for efficient flow.
  • Bearing play measured at operating speed.
  • Seal integrity tested at pressure.
  • Flow test against the original curve.

Failure symptoms

The weep hole under the housing lets a failing seal drip where it can be seen rather than contaminating the bearing. A small drip is a warning, not something to ignore until the bearing fails.

  • Weep from the drain hole or white crust
  • Rumbling or squealing from the front of the engine
  • Pulley or fan wobble
  • Overheating under load
  • Coolant smell after a run
  • Play in the pulley with the belt removed

Diagnosing overheating before replacing

Check coolant level and condition, confirm the thermostat opens, clean the radiator core, test the fan drive and inspect the belt for slip. A useful field test is to feel the radiator top and bottom hoses once warm: a large difference points to restricted flow through the core rather than a weak pump.

Installation and bleeding

Fit the pump to a clean surface with a new gasket, torque evenly and bleed the system completely. Trapped air creates local hot spots and can leave a new seal running dry for the first seconds after start-up.

  1. Drain coolant and dispose of it responsibly.
  2. Remove the belt and inspect the tensioner.
  3. Clean the block face and fit a new gasket.
  4. Torque bolts evenly in a cross pattern.
  5. Refill and bleed until the thermostat opens.
  6. Run to temperature, recheck level and look for weep.

Belt alignment and bearing life

Check the belt path with a straight edge across the pulleys before fitting the pump, and replace any tensioner or idler that shows play. A side-loaded bearing fails quickly and the failure is usually attributed to the pump rather than to the alignment.

Coolant quality

Use the specified coolant mixture and replace it at the recommended interval. Scale and contamination attack the seal faces, and plain water offers no protection at all. In dusty operations, clean the radiator core regularly as well.

Choosing the correct pump

Match the engine plate, the old pump number and the pulley dimensions. Send a photo of the old pump beside a ruler and we will confirm the casting before shipping.

Why a pump is rarely the only problem

A cooling system is a chain, and the pump is one link. A radiator with a blocked core, a thermostat that opens late or a fan that no longer locks up all produce the same overheating pattern. Replacing the pump without checking those parts is the most common wasted repair on these engines.

Why overheating is rarely the pump alone

A cooling system is a chain and the pump is one link. A blocked radiator core, a late-opening thermostat or a fan that no longer locks up all produce the same pattern. Checking those first prevents the most common wasted repair on these engines.

FAQ

Does the pump include a gasket?

Yes, the gasket and O-ring are supplied.

Can I drive with a weeping pump?

Only to reach a workshop.

Is the pulley included?

The pump comes with the hub.

How do I separate pump noise from belt noise?

Remove the belt and spin the pump by hand.

Related parts and categories

Browse the Weichai pump category, and pair the pump with the WP7 and WP8 water pump 610800060207 or the WP7 and WP8 full gasket kit 1001514985.

Description

Weichai WP7 Water Pump (1002372182). This pump maintains coolant velocity across the liners and through the head. Poor flow shows up as a temperature rise under load, not at idle.

Confirm the inlet angle and hose spigot position against the old pump. Two pumps can share a housing and differ in the direction the hose leaves.

Numbers beginning 1002 are numeric-series numbers used mainly on WP8 and WP9 assemblies and castings. On this engine, confirm the WP7 application against the engine plate before ordering.

Drain and refill with the correct coolant mix and bleed the system completely. Air in the system causes hot spots and accelerates cavitation damage on the liners.

Ordering note. Mixed pallets are accepted, so a single order can carry the block, the gasket set and the small seals together instead of arriving in three shipments.

Related reading: Cylinder Liner Cavitation: Causes, Symptoms and Prevention

We Are 30 Years Diesel Engine Parts Supplier
BrandEPID
Warranty12 Months
Condition100%New
More ModelsWeichai: WP7, WP7H, WP8, WP8H, and other Weichai series.
ShippingBy sea / air / express (DHL, FEDEX, TNT, UPS, EMS)
PackingStandard exporting packing or as required
Payment TermL/C, T/T, Western Union, Trade Assurance
Delivery Time3-7 days (depend on order)
Selling Point1. On-time Delivery   2. Genuine Quality Assurance   3. Professional Supplier

Construction and bench testing

The pump uses a cast iron housing, a precision cast impeller and a sealed bearing cartridge lubricated for life. The mechanical face seal is tested above operating pressure, and flow is measured at rated speed against the original curve.

  • Impeller clearance set for efficient flow.
  • Bearing play measured at operating speed.
  • Seal integrity tested at pressure.
  • Flow test against the original curve.

Failure symptoms

The weep hole under the housing lets a failing seal drip where it can be seen rather than contaminating the bearing. A small drip is a warning, not something to ignore until the bearing fails.

  • Weep from the drain hole or white crust
  • Rumbling or squealing from the front of the engine
  • Pulley or fan wobble
  • Overheating under load
  • Coolant smell after a run
  • Play in the pulley with the belt removed

Diagnosing overheating before replacing

Check coolant level and condition, confirm the thermostat opens, clean the radiator core, test the fan drive and inspect the belt for slip. A useful field test is to feel the radiator top and bottom hoses once warm: a large difference points to restricted flow through the core rather than a weak pump.

Installation and bleeding

Fit the pump to a clean surface with a new gasket, torque evenly and bleed the system completely. Trapped air creates local hot spots and can leave a new seal running dry for the first seconds after start-up.

  1. Drain coolant and dispose of it responsibly.
  2. Remove the belt and inspect the tensioner.
  3. Clean the block face and fit a new gasket.
  4. Torque bolts evenly in a cross pattern.
  5. Refill and bleed until the thermostat opens.
  6. Run to temperature, recheck level and look for weep.

Belt alignment and bearing life

Check the belt path with a straight edge across the pulleys before fitting the pump, and replace any tensioner or idler that shows play. A side-loaded bearing fails quickly and the failure is usually attributed to the pump rather than to the alignment.

Coolant quality

Use the specified coolant mixture and replace it at the recommended interval. Scale and contamination attack the seal faces, and plain water offers no protection at all. In dusty operations, clean the radiator core regularly as well.

Choosing the correct pump

Match the engine plate, the old pump number and the pulley dimensions. Send a photo of the old pump beside a ruler and we will confirm the casting before shipping.

Why a pump is rarely the only problem

A cooling system is a chain, and the pump is one link. A radiator with a blocked core, a thermostat that opens late or a fan that no longer locks up all produce the same overheating pattern. Replacing the pump without checking those parts is the most common wasted repair on these engines.

Why overheating is rarely the pump alone

A cooling system is a chain and the pump is one link. A blocked radiator core, a late-opening thermostat or a fan that no longer locks up all produce the same pattern. Checking those first prevents the most common wasted repair on these engines.

Related parts and categories

Browse the Weichai pump category, and pair the pump with the WP7 and WP8 water pump 610800060207 or the WP7 and WP8 full gasket kit 1001514985.

Detailed picture

Weichai WP7 WP8 Water Pump 1002372182 Diesel Engine Parts
Weichai WP7 WP8 Water Pump 1002372182 Diesel Engine Parts

Q&A

  • Does the pump include a gasket?

    Yes, the gasket and O-ring are supplied.

  • Can I drive with a weeping pump?

    Only to reach a workshop.

  • Is the pulley included?

    The pump comes with the hub.

  • How do I separate pump noise from belt noise?

    Remove the belt and spin the pump by hand.

Why buy from EPID

EPID supplies diesel engine parts for Weichai, Baudouin, Yuchai, Caterpillar, Sinotruk, FAW Xichai and Cummins engines. Every order is checked against the original part number before packing, and our team can identify a part from a photo of the engine plate. Ask for a quotation with your model and quantity and we will reply within one working day.

send message

    • [recaptcha]

    Home Tel Mail Inquiry