< img height="1" width="1" style="display:none" src="https://www.facebook.com/tr?id=2042618782839916&ev=PageView&noscript=1" />
Diesel Engines & Parts
Weichai WP7 WP8 Cylinder Head 610800040291 Diesel Engine Parts
Weichai WP7 WP8 Cylinder Head 610800040291 Diesel Engine Parts

Weichai WP7 WP8 Cylinder Head 610800040291 Diesel Engine Parts

Model: WP7 / WP8

Part Number: 610800040291

Brands: Weichai Power

Engine Model: WP7, WP7H, WP8, WP8H

Engine Type: Diesel

Scope of application: medium and heavy trucks, buses, construction machinery, generator sets

Another head casting in the WP7 and WP8 family

Weichai used several cylinder head castings on the WP7 and WP8 across production periods, and 610800040291 is one of them. Injector bore depth, port shape and coolant passage layout changed between generations, so a head from the wrong one fits the block and changes combustion.

Confirm the engine plate, the old casting number and the injector type before ordering. A head that looks identical on the outside can behave very differently once the engine runs, and the fault usually appears as hard starting, smoke or a coolant leak at the rear.

Casting and machining checks

Each head is cast in high-grade iron, stress relieved and machined. The checks that decide whether it will hold are all dimensional and can be supplied on request.

  • Deck flatness measured in both directions.
  • Valve seat width and concentricity.
  • Guide bore clearance for oil control.
  • Injector bore depth and seat angle.
  • Pressure test of water jacket and exhaust ports.

Symptoms that point to the head

Head failures usually begin with cooling. A restricted radiator or a tired water pump raises metal temperature, the deck warps and the gasket loses its grip.

  • Coolant disappearing with no visible external leak
  • Bubbles in the radiator or coolant pushed out of the filler
  • White smoke that persists after warm-up
  • Coolant in the oil, visible as a milky dipstick
  • Compression loss on two adjacent cylinders
  • Overheating that returns after a thermostat replacement

Fitting the new head

Preparation decides the outcome. Clean the block deck to bare metal, check flatness with a straight edge and a feeler gauge, and confirm that the head bolts are new before starting.

  1. Fit a new gasket dry, without sealant.
  2. Torque in three stages in the factory sequence, then angle tighten.
  3. Set valve clearance after the engine has run and cooled.
  4. Fill and bleed the cooling system with the specified mixture.
  5. Recheck injector clamp torque after the first hours.

Valve guides and oil consumption

Worn guides let oil down the stems, producing blue smoke at start-up that clears once the engine works. That pattern is often mistaken for worn rings, and the rebuild then goes in the wrong direction. Measuring guide clearance settles the question on the bench.

Repair or replace

Light seat wear can be re-cut and a mildly warped deck machined once if enough material remains. Cracks between seats, at the injector bore or across the deck are not economically repairable.

Cooling system care

Keep coolant at the correct concentration, clean the radiator core in dusty conditions and replace the thermostat on schedule. On construction and agricultural engines, the core is often packed with dust, which raises temperature without any component fault.

Head bolts and clamping load

Head bolts are torque-to-yield and must be replaced every time the head is removed. Reusing them reduces clamping force, and the gasket then leaks at high load.

Choosing the correct head

Match the engine plate, the old casting number and the injector type. Send photographs of the old head and the nameplate and our team will confirm the variant before shipping.

Why head numbers change within a family

Head castings are revised when injector, port or coolant design changes. A head from another generation fits the block but changes combustion, and the resulting symptoms look like a fuel problem. The casting number and the injector seat are the features that identify the generation.

What a pressure test finds and what it misses

A pressure test fills the water jacket above operating pressure and looks for loss. It finds cracks through the jacket and into a port, but it does not find a deck that is warped yet still sealed. Flatness is measured separately with a straight edge, and both checks are needed.

Deck preparation before fitting

Scrape the block deck and head face to bare metal, then wipe with a suitable solvent. Avoid rotary abrasive discs, which remove metal unevenly and change the flatness that was just measured. Debris left in a coolant passage travels to a thermostat and causes a fault weeks later.

Valve train parts to renew with the head

If the head is being replaced because of valve damage, renew valves, springs and retainers as a set. Reusing springs that have lost tension with new valves produces a valve train that floats at high speed, and on a working engine that shows as a misfire under load rather than at idle.

Ask us for the valve kit that matches the casting when ordering, so the head and valve train arrive together and the workshop is not waiting on a second shipment.

FAQ

Does the head come with valves?

Yes, unless a bare head is requested.

Can I reuse the head bolts?

No. They must be replaced every time.

How do I confirm a crack?

A pressure test and a combustion gas test confirm it.

Are heads interchangeable between variants?

No. Confirm the casting number.

Related parts and categories

Browse the Weichai cylinder head category, and pair the head with the WP7 and WP8 cylinder head 1003785218 or the WP7 and WP8 full gasket kit 1001514985.

Description

Weichai WP7 Cylinder Head (610800040291). The head carries combustion pressure, the valve train and the injectors, and it has to seal all three against a block that expands at a different rate. It is the most highly stressed casting in the engine.

Photograph the deck, the casting number and the old gasket. Those three images usually identify the revision before anything ships, and they are far cheaper than a returned head.

Numbers beginning 6108 belong to the WP7 and WP8 families. These engines share architecture but differ in detail, so a part that fits one will not necessarily suit the other without checking the casting. On this engine, confirm the WP7 application against the engine plate before ordering.

Have the head checked for flatness and, where necessary, pressure tested before assembly. A crack that does not leak cold will open once the engine reaches temperature.

Ordering note. Payment terms and shipping method are confirmed in writing before dispatch, including the port of loading and the estimated transit time.

Related reading: Cylinder Head Rebuild: Valves, Guides and Seats

We Are 30 Years Diesel Engine Parts Supplier
BrandEPID
Warranty12 Months
Condition100%New
More ModelsWeichai: WP7, WP7H, WP8, WP8H, and other Weichai series.
ShippingBy sea / air / express (DHL, FEDEX, TNT, UPS, EMS)
PackingStandard exporting packing or as required
Payment TermL/C, T/T, Western Union, Trade Assurance
Delivery Time3-7 days (depend on order)
Selling Point1. On-time Delivery   2. Genuine Quality Assurance   3. Professional Supplier

Symptoms that point to the head

Head failures usually begin with cooling. A restricted radiator or a tired water pump raises metal temperature, the deck warps and the gasket loses its grip.

  • Coolant disappearing with no visible external leak
  • Bubbles in the radiator or coolant pushed out of the filler
  • White smoke that persists after warm-up
  • Coolant in the oil, visible as a milky dipstick
  • Compression loss on two adjacent cylinders
  • Overheating that returns after a thermostat replacement

Fitting the new head

Preparation decides the outcome. Clean the block deck to bare metal, check flatness with a straight edge and a feeler gauge, and confirm that the head bolts are new before starting.

  1. Fit a new gasket dry, without sealant.
  2. Torque in three stages in the factory sequence, then angle tighten.
  3. Set valve clearance after the engine has run and cooled.
  4. Fill and bleed the cooling system with the specified mixture.
  5. Recheck injector clamp torque after the first hours.

Valve guides and oil consumption

Worn guides let oil down the stems, producing blue smoke at start-up that clears once the engine works. That pattern is often mistaken for worn rings, and the rebuild then goes in the wrong direction. Measuring guide clearance settles the question on the bench.

Repair or replace

Light seat wear can be re-cut and a mildly warped deck machined once if enough material remains. Cracks between seats, at the injector bore or across the deck are not economically repairable.

Cooling system care

Keep coolant at the correct concentration, clean the radiator core in dusty conditions and replace the thermostat on schedule. On construction and agricultural engines, the core is often packed with dust, which raises temperature without any component fault.

Head bolts and clamping load

Head bolts are torque-to-yield and must be replaced every time the head is removed. Reusing them reduces clamping force, and the gasket then leaks at high load.

Choosing the correct head

Match the engine plate, the old casting number and the injector type. Send photographs of the old head and the nameplate and our team will confirm the variant before shipping.

Why head numbers change within a family

Head castings are revised when injector, port or coolant design changes. A head from another generation fits the block but changes combustion, and the resulting symptoms look like a fuel problem. The casting number and the injector seat are the features that identify the generation.

What a pressure test finds and what it misses

A pressure test fills the water jacket above operating pressure and looks for loss. It finds cracks through the jacket and into a port, but it does not find a deck that is warped yet still sealed. Flatness is measured separately with a straight edge, and both checks are needed.

Deck preparation before fitting

Scrape the block deck and head face to bare metal, then wipe with a suitable solvent. Avoid rotary abrasive discs, which remove metal unevenly and change the flatness that was just measured. Debris left in a coolant passage travels to a thermostat and causes a fault weeks later.

Valve train parts to renew with the head

If the head is being replaced because of valve damage, renew valves, springs and retainers as a set. Reusing springs that have lost tension with new valves produces a valve train that floats at high speed, and on a working engine that shows as a misfire under load rather than at idle.

Ask us for the valve kit that matches the casting when ordering, so the head and valve train arrive together and the workshop is not waiting on a second shipment.

Related parts and categories

Browse the Weichai cylinder head category, and pair the head with the WP7 and WP8 cylinder head 1003785218 or the WP7 and WP8 full gasket kit 1001514985.

Detailed picture

Weichai WP7 WP8 Cylinder Head 610800040291 Diesel Engine Parts
Weichai WP7 WP8 Cylinder Head 610800040291 Diesel Engine Parts

Q&A

  • Does the head come with valves?

    Yes, unless a bare head is requested.

  • Can I reuse the head bolts?

    No. They must be replaced every time.

  • How do I confirm a crack?

    A pressure test and a combustion gas test confirm it.

  • Are heads interchangeable between variants?

    No. Confirm the casting number.

Why buy from EPID

EPID supplies diesel engine parts for Weichai, Baudouin, Yuchai, Caterpillar, Sinotruk, FAW Xichai and Cummins engines. Every order is checked against the original part number before packing, and our team can identify a part from a photo of the engine plate. Ask for a quotation with your model and quantity and we will reply within one working day.

send message

    • [recaptcha]

    Home Tel Mail Inquiry