

Model: WP7 / WP8
Part Number: 1012669823
Brands: Weichai Power
Engine Model: WP7, WP7H, WP8, WP8H
Engine Type: Diesel
Scope of application: medium and heavy trucks, buses, construction machinery, generator sets
Head castings on the WP7 and WP8 were revised repeatedly, and 1012669823 belongs to the later part of that series. Injector bore depth, port shape and coolant outlet position all changed between generations, so a head from a neighbouring variant bolts up, runs, and behaves differently. Those differences show up as smoke, hard starting or a coolant leak at the rear of the head.
Confirm the engine plate, the old casting number and the injector type before ordering. Send photographs of the old head and the nameplate and our team will confirm the variant before the consignment ships, which is far cheaper than returning a head from an overseas port.
Each head is cast in high-grade iron, stress relieved and machined on the deck, valve seats, guides and injector bores. The checks that decide whether it will hold are dimensional, and the measurements can be supplied on request.
Head failures begin with cooling. A restricted radiator or a tired water pump raises metal temperature, the deck warps and the gasket loses its grip. The early symptoms are easily mistaken for injector problems and are often chased for weeks before the head is suspected.
Preparation decides the outcome. Clean the block deck to bare metal, check flatness with a straight edge and feeler gauge, and confirm that the head bolts are new before starting. No gasket compensates for a deck that is out of specification.
A pressure test fills the water jacket above operating pressure and looks for loss. It finds cracks through the jacket and into a port, but it does not find a deck that is warped yet still sealed. Flatness is measured separately with a straight edge, and both checks are needed before a head is fitted.
Worn guides let oil down the stems, producing blue smoke at start-up that clears once the engine works. That pattern is often mistaken for worn rings, and the rebuild then goes in the wrong direction. Measuring guide clearance on the bench takes minutes and settles the question before parts are ordered.
Light seat wear can be re-cut and a mildly warped deck machined once if enough material remains. Cracks between seats, at the injector bore or across the deck are not economically repairable, and a repaired head that fails again usually takes the gasket with it.
If the head is replaced because of valve damage, renew valves, springs and retainers as a set. Reusing springs that have lost tension with new valves produces a valve train that floats at high speed, which shows as a misfire under load rather than at idle.
Keep coolant at the correct concentration, clean the radiator core in dusty conditions and replace the thermostat on schedule. On construction and agricultural engines the core is often packed with dust, which raises temperature without any component fault at all.
Head bolts are torque-to-yield and must be replaced every time the head is removed. Reusing them reduces clamping force, and the gasket then leaks at high load. Order a new bolt set with every head rather than discovering the need halfway through assembly.
Yes, unless a bare head is requested.
No. They must be replaced every time.
A pressure test and a combustion gas test confirm it.
No. Confirm the casting number against the engine plate.
Browse the Weichai cylinder head category, and pair the head with the WP7 and WP8 cylinder head 1003125852 or the WP7 and WP8 full gasket kit 1001514985.
Weichai WP7 Cylinder Head (1012669823). This casting closes the combustion chamber and carries the injector bores, the valve seats and the coolant passages. Its flatness and injector bore depth decide whether the engine runs cleanly or smokes.
Compare the old head gasket with the new one before the engine is stripped: fire ring position, coolant hole pattern and thickness. If any of the three differ, check the casting number against the engine plate.
The part number is the reliable identifier here. Where the old number is unreadable, measure the component and compare it with the drawing rather than guessing from the engine model. On this engine, confirm the WP7 application against the engine plate before ordering.
Have the head checked for flatness and, where necessary, pressure tested before assembly. A crack that does not leak cold will open once the engine reaches temperature.
Ordering note. Payment terms and shipping method are confirmed in writing before dispatch, including the port of loading and the estimated transit time.
Related reading: Cylinder Head Rebuild: Valves, Guides and Seats
| We Are 30 Years Diesel Engine Parts Supplier | |
| Brand | EPID |
| Warranty | 12 Months |
| Condition | 100%New |
| More Models | Weichai: WP7, WP7H, WP8, WP8H, and other Weichai series. |
| Shipping | By sea / air / express (DHL, FEDEX, TNT, UPS, EMS) |
| Packing | Standard exporting packing or as required |
| Payment Term | L/C, T/T, Western Union, Trade Assurance |
| Delivery Time | 3-7 days (depend on order) |
| Selling Point | 1. On-time Delivery 2. Genuine Quality Assurance 3. Professional Supplier |
Head failures begin with cooling. A restricted radiator or a tired water pump raises metal temperature, the deck warps and the gasket loses its grip. The early symptoms are easily mistaken for injector problems and are often chased for weeks before the head is suspected.
Preparation decides the outcome. Clean the block deck to bare metal, check flatness with a straight edge and feeler gauge, and confirm that the head bolts are new before starting. No gasket compensates for a deck that is out of specification.
A pressure test fills the water jacket above operating pressure and looks for loss. It finds cracks through the jacket and into a port, but it does not find a deck that is warped yet still sealed. Flatness is measured separately with a straight edge, and both checks are needed before a head is fitted.
Worn guides let oil down the stems, producing blue smoke at start-up that clears once the engine works. That pattern is often mistaken for worn rings, and the rebuild then goes in the wrong direction. Measuring guide clearance on the bench takes minutes and settles the question before parts are ordered.
Light seat wear can be re-cut and a mildly warped deck machined once if enough material remains. Cracks between seats, at the injector bore or across the deck are not economically repairable, and a repaired head that fails again usually takes the gasket with it.
If the head is replaced because of valve damage, renew valves, springs and retainers as a set. Reusing springs that have lost tension with new valves produces a valve train that floats at high speed, which shows as a misfire under load rather than at idle.
Keep coolant at the correct concentration, clean the radiator core in dusty conditions and replace the thermostat on schedule. On construction and agricultural engines the core is often packed with dust, which raises temperature without any component fault at all.
Head bolts are torque-to-yield and must be replaced every time the head is removed. Reusing them reduces clamping force, and the gasket then leaks at high load. Order a new bolt set with every head rather than discovering the need halfway through assembly.
Browse the Weichai cylinder head category, and pair the head with the WP7 and WP8 cylinder head 1003125852 or the WP7 and WP8 full gasket kit 1001514985.


Yes, unless a bare head is requested.
No. They must be replaced every time.
A pressure test and a combustion gas test confirm it.
No. Confirm the casting number against the engine plate.
EPID supplies diesel engine parts for Weichai, Baudouin, Yuchai, Caterpillar, Sinotruk, FAW Xichai and Cummins engines. Every order is checked against the original part number before packing, and our team can identify a part from a photo of the engine plate. Ask for a quotation with your model and quantity and we will reply within one working day.