

Model: WP13
Part Number: 1002427237
Brands: Weichai Power
Engine Model: WP13, WP13.480, WP13.500, WP13.550, WP13.580
Engine Type: Diesel
Scope of application: heavy haulage trucks, mining dump trucks, construction machinery, generator sets
Weichai WP13 oil pumps appear under both 6127 and 1002 number prefixes, and 1002427237 belongs to the second group. As with the others in this family, the differences are in the drive and pick-up rather than in the pumping element, so a pump from the wrong group may bolt up and still not feed correctly. Confirm the engine plate and the old pump number, and check the front cover if the engine has been rebuilt.
A 13-litre engine has a large bearing area to feed and a turbocharger that needs constant oil supply. The pump must deliver volume at hot idle and hold pressure at rated speed without exceeding its relief valve setting. Wear shows first as a pressure drop at hot idle rather than as a loss of peak pressure, which is why a gauge reading taken only at speed can be misleading.
Every pump is run on a test bench, because the difference between a serviceable pump and a worn one is a few percent of flow that no visual check reveals. Flow is measured at rated speed, the relief valve is opened and recorded, gear backlash and end clearance are measured, and the housing and pick-up joint are leak tested.
Low pressure is the headline symptom, but the circumstances matter. Pressure that is low only when hot points as much to worn bearings as to the pump, while pressure that recovers instantly with engine speed points to the relief valve or clearances. The warning light usually appears at hot idle after a climb, exactly when the oil is thinnest.
Check oil level and condition, replace the filter, inspect the strainer, then measure pressure with a mechanical gauge. Only after those steps should the relief valve and the pump come under suspicion, because a blocked strainer and a faulty sender both imitate a worn pump. Recording cold idle, hot idle and rated speed gives a clear diagnosis.
Priming decides whether the bearings survive the first minute after assembly. A dry pump takes time to draw oil, and the bearings run unprotected while it does. Prime with clean oil, turn the engine by hand until oil reaches the head, and only then start.
On these engines the pump also supplies the piston cooling jets, which is easy to forget when diagnosing pressure alone. A pump that holds pressure but has lost volume still allows crown temperatures to climb, and the damage appears as a scored piston rather than low oil pressure. If pistons have failed without an obvious cause, measure flow first.
Match the part number, the engine rating and the drive type. If the front cover has been replaced, check that the mounting face and drive gear match. Send a photograph of the old pump beside a ruler and we will confirm the casting before shipping.
Most premature failures come from contaminated oil. Use the specified grade, change it at the severe-duty interval and never run with a leaking injector that thins the oil with diesel. Keep the cooling system healthy, because sustained overheating reduces oil film strength at the bearings.
Regular oil analysis catches bearing wear before pressure starts to fall. Rising iron and lead indicate that the oil film is breaking down somewhere in the engine, and the pump is one of the first parts worth checking. Analysis costs little compared with a crankshaft.
Two WP13 pumps can share the same housing casting and differ only in the drive gear or pick-up tube. That is why a photo of the old pump beside a ruler, with the drive end visible, is more useful than a part number alone when the engine has been rebuilt or the front cover replaced.
If pressure is low at hot idle and the engine has covered high hours, replacing the pump during the same overhaul is usually cheaper than diagnosing it separately. The pump is inexpensive compared with the labour of opening the front cover twice, and a new pump removes one variable from the pressure problem.
Yes, the mounting gasket and O-ring are supplied.
Yes. A blocked strainer, stuck relief valve, worn bearings or a faulty sender all mimic pump failure.
The pump comes with its drive gear fitted and timed as original.
At every major overhaul, or whenever the front cover is removed.
Browse the Weichai pump category, and pair the pump with the WP13 oil pump 612700010009 or the WP13 cylinder block 612700010001.
Weichai WP13 Oil Pump (1002427237). Lubrication starts here. The gear set, relief valve and drive must all match the housing, and a mismatch shows up as low pressure from the first start.
Compare the old pump number and photograph the drive end. A pump with the wrong drive bolts up and fails to feed correctly.
Numbers beginning 1002 are numeric-series numbers used mainly on WP8 and WP9 assemblies and castings. On this engine, confirm the WP13 application against the engine plate before ordering.
Prime the pump before the first start and confirm oil pressure at the gauge before allowing the engine to run. Never crank a fresh rebuild hoping pressure will arrive.
Ordering note. Mixed pallets are accepted, so a single order can carry the block, the gasket set and the small seals together instead of arriving in three shipments.
Related reading: Oil Pump Diagnosis: Low Pressure, Wear and Replacement
| We Are 30 Years Diesel Engine Parts Supplier | |
| Brand | EPID |
| Warranty | 12 Months |
| Condition | 100%New |
| More Models | Weichai: WP13, WP13.480, WP13.500, WP13.550, WP13.580, and other Weichai series. |
| Shipping | By sea / air / express (DHL, FEDEX, TNT, UPS, EMS) |
| Packing | Standard exporting packing or as required |
| Payment Term | L/C, T/T, Western Union, Trade Assurance |
| Delivery Time | 3-7 days (depend on order) |
| Selling Point | 1. On-time Delivery 2. Genuine Quality Assurance 3. Professional Supplier |
Every pump is run on a test bench, because the difference between a serviceable pump and a worn one is a few percent of flow that no visual check reveals. Flow is measured at rated speed, the relief valve is opened and recorded, gear backlash and end clearance are measured, and the housing and pick-up joint are leak tested.
Low pressure is the headline symptom, but the circumstances matter. Pressure that is low only when hot points as much to worn bearings as to the pump, while pressure that recovers instantly with engine speed points to the relief valve or clearances. The warning light usually appears at hot idle after a climb, exactly when the oil is thinnest.
Check oil level and condition, replace the filter, inspect the strainer, then measure pressure with a mechanical gauge. Only after those steps should the relief valve and the pump come under suspicion, because a blocked strainer and a faulty sender both imitate a worn pump. Recording cold idle, hot idle and rated speed gives a clear diagnosis.
Priming decides whether the bearings survive the first minute after assembly. A dry pump takes time to draw oil, and the bearings run unprotected while it does. Prime with clean oil, turn the engine by hand until oil reaches the head, and only then start.
On these engines the pump also supplies the piston cooling jets, which is easy to forget when diagnosing pressure alone. A pump that holds pressure but has lost volume still allows crown temperatures to climb, and the damage appears as a scored piston rather than low oil pressure. If pistons have failed without an obvious cause, measure flow first.
Match the part number, the engine rating and the drive type. If the front cover has been replaced, check that the mounting face and drive gear match. Send a photograph of the old pump beside a ruler and we will confirm the casting before shipping.
Most premature failures come from contaminated oil. Use the specified grade, change it at the severe-duty interval and never run with a leaking injector that thins the oil with diesel. Keep the cooling system healthy, because sustained overheating reduces oil film strength at the bearings.
Regular oil analysis catches bearing wear before pressure starts to fall. Rising iron and lead indicate that the oil film is breaking down somewhere in the engine, and the pump is one of the first parts worth checking. Analysis costs little compared with a crankshaft.
Two WP13 pumps can share the same housing casting and differ only in the drive gear or pick-up tube. That is why a photo of the old pump beside a ruler, with the drive end visible, is more useful than a part number alone when the engine has been rebuilt or the front cover replaced.
If pressure is low at hot idle and the engine has covered high hours, replacing the pump during the same overhaul is usually cheaper than diagnosing it separately. The pump is inexpensive compared with the labour of opening the front cover twice, and a new pump removes one variable from the pressure problem.
Browse the Weichai pump category, and pair the pump with the WP13 oil pump 612700010009 or the WP13 cylinder block 612700010001.


Yes, the mounting gasket and O-ring are supplied.
Yes. A blocked strainer, stuck relief valve, worn bearings or a faulty sender all mimic pump failure.
The pump comes with its drive gear fitted and timed as original.
At every major overhaul, or whenever the front cover is removed.
EPID supplies diesel engine parts for Weichai, Baudouin, Yuchai, Caterpillar, Sinotruk, FAW Xichai and Cummins engines. Every order is checked against the original part number before packing, and our team can identify a part from a photo of the engine plate. Ask for a quotation with your model and quantity and we will reply within one working day.