< img height="1" width="1" style="display:none" src="https://www.facebook.com/tr?id=2042618782839916&ev=PageView&noscript=1" />
Diesel Engines & Parts
Baudouin 4M10G88 Piston Ring Set 1004934488 Marine Diesel Parts
Baudouin 4M10G88 Piston Ring Set 1004934488 Marine Diesel Parts
Baudouin 4M10G88 Piston Ring Set 1004934488 Marine Diesel Parts
Baudouin 4M10G88 Piston Ring Set 1004934488 Marine Diesel Parts

Baudouin 4M10G88 Piston Ring Set 1004934488 Marine Diesel Parts

Model: 4M10G88

Part Number: 1004934488

Brands: Baudouin

Engine Model: 4M10G88

Engine Type: Marine and industrial diesel

Scope of application: marine propulsion, marine auxiliary, generator sets

Rings on the mid-rated 4M10G

Set 1004934488 is specific to the Baudouin 4M10G88, which sits between the G70 and G110 in the range. The G88 is a common choice for auxiliary and light propulsion duty, running at moderate load for long periods.

Rings seal combustion gas, conduct heat into the liner and scrape oil back to the sump. When they wear, the engine does not stop; it becomes weak and smoky, and on a genset the first sign is frequency droop under load.

Why the ring set is rating specific

Rings are matched to the piston groove geometry and compression ratio of each rating. Fitting a G70 or G110 set to a G88 produces uneven tension, wrong end gaps and oil consumption that no adjustment can fix.

Construction and inspection

  • Ring thickness and radial tension matched to the groove.
  • Face coating verified for wear resistance.
  • End gap measured in the actual bore.
  • Markings clear so the top face cannot be inverted.

Symptoms of worn rings

  • Oil consumption rising without external leaks
  • Blue smoke at start-up and under load
  • Crankcase pressure pushing oil out of the breather
  • Compression low dry, slightly better with oil added
  • Glazed or polished liners
  • Rated output no longer reached

Fitting procedure

  1. Clean the piston grooves to bare metal.
  2. Check side clearance with a feeler gauge.
  3. Fit the oil ring expander then the rails.
  4. Stagger the end gaps around the piston.
  5. Oil the rings and fit with a ring compressor.
  6. Break in with varying load and change oil afterwards.

Measuring ring gaps correctly

Measure in the liner the ring will run in, with the ring pushed square to a depth near the bottom of ring travel. Measuring in a different bore, or tilted, gives a reading that is wrong by enough to cause a failure.

Inspecting pistons before fitting rings

New rings cannot fix a worn piston. Measure groove width with the old ring; an opened groove lets the ring flutter and break. Clean carbon out of the groove corner properly rather than scraping the surface.

Oil control and smoke

Oil that passes the rings burns in the cylinder and produces the blue haze that owners notice first. On a marine engine that haze is often dismissed as normal for a working boat, which is why oil consumption records matter more than the exhaust.

Break-in and oil choice

Run at varying load after the rebuild, increasing gradually, and change oil early. A high-detergent oil can slow bedding-in, so follow the workshop recommendation for the break-in period rather than the normal service oil.

Fuel quality and ring life

Marine fuel varies widely and poor fuel accelerates ring and liner wear. Keep fuel filters changed and injectors serviced at the recommended hours. A leaking injector washes the bore and dilutes the oil.

Oil consumption after a rebuild

Track consumption against the engine log after the first hundred hours. A steady figure means the rings seated; a rising figure means a gap or bore finish problem that should be found before it becomes bore damage.

Maintenance for ring life

Clean air and correct oil keep rings alive. Keep the intake clean, use the specified oil grade and change it at the hours-based interval. Fix overheating promptly.

Storing rings before fitting

Rings are supplied in protective sleeves because a bare ring can rust in a humid engine room. Keep them wrapped until the pistons are ready and never mix rings between sets.

Why ring sets are replaced as a whole

It is tempting to replace only the compression rings when the oil ring still looks serviceable, but the three rings wear as a set. The oil ring expander often loses tension before the compression rings show visible wear, and reusing it with new compression rings produces oil consumption that looks like a machining fault.

Replace all three rings per piston and keep the set together. The cost of the rings is small compared with the labour of opening the engine a second time.

Oil quality and ring sealing

The oil grade affects how quickly rings bed in and how well they seal afterwards. A grade that is too thin at operating temperature lets oil past the rings; one that is too thick can starve the upper cylinder at start-up. Use the grade specified for the engine and the ambient conditions it works in.

FAQ

Does the set fit G70 and G110 engines?

No. Each rating has its own specification.

How many rings in the set?

One set covers one piston.

Do I need to file the gaps?

Only if the measured gap requires adjustment.

What causes oil use after a rebuild?

Glazed bores, wrong gaps or rings fitted upside down.

Related parts and categories

Browse the Baudouin piston and components category, and pair the rings with the 4M10G88 piston 1004934487 or the 4M10G cylinder liner 1000156635.

Description

Baudouin 4M10G88 Piston Ring (1004934488). These rings are the interface between piston and bore. Their radial tension and face profile decide whether the engine burns oil or blows it out of the breather.

Measure the old ring thickness and radial depth against the new set. A set that fits the groove loosely will flutter and break rather than seal.

Numbers beginning 1004 are numeric-series numbers used on later WP7 and WP8 production, where mounting detail changed without a change of nominal type. On this engine, confirm the 4M10G88 application against the engine plate before ordering.

Measure end gaps in the bore the ring will actually run in, with the ring squared by the piston crown. Measuring at the top of the bore or in a different liner gives a false reading.

Ordering note. Packing is export grade: each unit is wrapped, boxed and palletised for sea freight, with the part number marked on the outside so the receiving store can book it in without opening the carton.

Related reading: Piston Ring Selection: Gap, Tension and Bore Condition

We Are 30 Years Diesel Engine Parts Supplier
BrandEPID
Warranty12 Months
Condition100%New
More ModelsWeichai: 4M10G88, and other Weichai series.
ShippingBy sea / air / express (DHL, FEDEX, TNT, UPS, EMS)
PackingStandard exporting packing or as required
Payment TermL/C, T/T, Western Union, Trade Assurance
Delivery Time3-7 days (depend on order)
Selling Point1. On-time Delivery   2. Genuine Quality Assurance   3. Professional Supplier

Construction and inspection

  • Ring thickness and radial tension matched to the groove.
  • Face coating verified for wear resistance.
  • End gap measured in the actual bore.
  • Markings clear so the top face cannot be inverted.

Symptoms of worn rings

  • Oil consumption rising without external leaks
  • Blue smoke at start-up and under load
  • Crankcase pressure pushing oil out of the breather
  • Compression low dry, slightly better with oil added
  • Glazed or polished liners
  • Rated output no longer reached

Fitting procedure

  1. Clean the piston grooves to bare metal.
  2. Check side clearance with a feeler gauge.
  3. Fit the oil ring expander then the rails.
  4. Stagger the end gaps around the piston.
  5. Oil the rings and fit with a ring compressor.
  6. Break in with varying load and change oil afterwards.

Measuring ring gaps correctly

Measure in the liner the ring will run in, with the ring pushed square to a depth near the bottom of ring travel. Measuring in a different bore, or tilted, gives a reading that is wrong by enough to cause a failure.

Inspecting pistons before fitting rings

New rings cannot fix a worn piston. Measure groove width with the old ring; an opened groove lets the ring flutter and break. Clean carbon out of the groove corner properly rather than scraping the surface.

Oil control and smoke

Oil that passes the rings burns in the cylinder and produces the blue haze that owners notice first. On a marine engine that haze is often dismissed as normal for a working boat, which is why oil consumption records matter more than the exhaust.

Break-in and oil choice

Run at varying load after the rebuild, increasing gradually, and change oil early. A high-detergent oil can slow bedding-in, so follow the workshop recommendation for the break-in period rather than the normal service oil.

Fuel quality and ring life

Marine fuel varies widely and poor fuel accelerates ring and liner wear. Keep fuel filters changed and injectors serviced at the recommended hours. A leaking injector washes the bore and dilutes the oil.

Oil consumption after a rebuild

Track consumption against the engine log after the first hundred hours. A steady figure means the rings seated; a rising figure means a gap or bore finish problem that should be found before it becomes bore damage.

Maintenance for ring life

Clean air and correct oil keep rings alive. Keep the intake clean, use the specified oil grade and change it at the hours-based interval. Fix overheating promptly.

Storing rings before fitting

Rings are supplied in protective sleeves because a bare ring can rust in a humid engine room. Keep them wrapped until the pistons are ready and never mix rings between sets.

Why ring sets are replaced as a whole

It is tempting to replace only the compression rings when the oil ring still looks serviceable, but the three rings wear as a set. The oil ring expander often loses tension before the compression rings show visible wear, and reusing it with new compression rings produces oil consumption that looks like a machining fault.

Replace all three rings per piston and keep the set together. The cost of the rings is small compared with the labour of opening the engine a second time.

Oil quality and ring sealing

The oil grade affects how quickly rings bed in and how well they seal afterwards. A grade that is too thin at operating temperature lets oil past the rings; one that is too thick can starve the upper cylinder at start-up. Use the grade specified for the engine and the ambient conditions it works in.

Related parts and categories

Browse the Baudouin piston and components category, and pair the rings with the 4M10G88 piston 1004934487 or the 4M10G cylinder liner 1000156635.

Detailed picture

Baudouin 4M10G88 Piston Ring Set 1004934488 Marine Diesel Parts
Baudouin 4M10G88 Piston Ring Set 1004934488 Marine Diesel Parts
Baudouin 4M10G88 Piston Ring Set 1004934488 Marine Diesel Parts
Baudouin 4M10G88 Piston Ring Set 1004934488 Marine Diesel Parts

Q&A

  • Does the set fit G70 and G110 engines?

    No. Each rating has its own specification.

  • How many rings in the set?

    One set covers one piston.

  • Do I need to file the gaps?

    Only if the measured gap requires adjustment.

  • What causes oil use after a rebuild?

    Glazed bores, wrong gaps or rings fitted upside down.

Why buy from EPID

EPID supplies diesel engine parts for Weichai, Baudouin, Yuchai, Caterpillar, Sinotruk, FAW Xichai and Cummins engines. Every order is checked against the original part number before packing, and our team can identify a part from a photo of the engine plate. Ask for a quotation with your model and quantity and we will reply within one working day.

send message

    • [recaptcha]

    Home Tel Mail Inquiry