< img height="1" width="1" style="display:none" src="https://www.facebook.com/tr?id=2042618782839916&ev=PageView&noscript=1" />
Diesel Engines & Parts
Baudouin 4M10G110 Full Gasket Kit 1002224369 Marine Diesel Parts
Baudouin 4M10G110 Full Gasket Kit 1002224369 Marine Diesel Parts

Baudouin 4M10G110 Full Gasket Kit 1002224369 Marine Diesel Parts

Model: 4M10G110

Part Number: 1002224369

Brands: Baudouin

Engine Model: 4M10G110

Engine Type: Marine and industrial diesel

Scope of application: marine propulsion, marine auxiliary, generator sets

The second gasket specification for the G110

Baudouin used more than one gasket specification for the 4M10G110 across production periods. Kit 1002224369 is the alternative to 7000002541, and which one is correct depends on the head casting fitted to the engine rather than on the model name alone.

That distinction matters because a gasket from the wrong specification will bolt up and then leak. The leak is usually blamed on the gasket quality, when the real problem was a mismatch between the gasket and the head face.

What the kit contains

  • Head gasket matched to the corresponding head casting.
  • Valve cover and manifold gaskets.
  • Oil pan gasket and timing cover seals.
  • Crank seals and pump seals.
  • Injector copper washers and small O-rings.

How to tell which specification you need

Put the old head gasket on a flat surface next to the new one. Fire ring position, coolant hole pattern and overall thickness are the three features that matter, and all three are visible when the two are side by side. If any of them differ, stop and check the head casting number before the engine is stripped.

Why the head gasket is the deciding part

The rest of the kit is common enough that two specifications can look identical on the bench. The head gasket is the part that must match the casting, and it is also the part whose failure causes the most damage. Spend the time comparing it before the engine comes apart.

Symptoms of a failed gasket set

  • Oil weeping from the pan rail or rear main
  • Coolant seeping at the pump or thermostat housing
  • Soot marks around manifold joints
  • Bubbles in the heat exchanger
  • Oil and coolant mixing
  • Compression loss between adjacent cylinders

Installation notes

  1. Clean every mating surface to bare metal.
  2. Check head and block deck flatness.
  3. Fit the steel head gasket dry.
  4. Use new head bolts and torque in the factory sequence.
  5. Apply anaerobic sealant only where specified.
  6. Recheck for leaks after the first heat cycle.

Head bolts and clamping load

Head bolts are torque-to-yield and must be replaced every time the head is removed. Reusing them is the most common reason a new gasket fails early, and the failure is usually blamed on the gasket rather than on the bolts.

Diagnosing which gasket failed

A head gasket failure consumes coolant and pressurises the cooling system. A manifold failure leaves soot tracks and a whistle under load. A rear seal failure leaves oil at the bell housing rather than at the pan. Identifying the failure tells you whether a full kit is needed at all.

Working safely on a marine engine

Never open a pressurised cooling system while hot. The expansion tank on a boat can be above head height, and releasing the cap can spray scalding coolant. Let the engine cool completely, then release slowly.

Storage and handling

Store the kit flat, dry and out of sunlight. Composite gaskets absorb moisture slowly, so a kit stored in a damp engine room should be inspected before fitting. Keep the head gasket in its carton until the deck is ready.

Photographs that identify the specification

Send one photo of the old head gasket on a flat surface with a ruler alongside, one of the head casting number and one of the engine plate. Those three images let our team confirm the specification with confidence instead of guessing from the model name.

Freight and consolidation

Kits are light and compact and consolidate well with liners or pistons. Tell us what else is in the shipment so the kit is packed on top and not crushed by heavy parts.

Preparing the surfaces before the gasket goes on

The best gasket in the world will not seal a surface that has old material on it. Scrape the block deck and head face to bare metal, then wipe both with a suitable solvent. Avoid rotary abrasive discs, which remove metal unevenly and change the flatness that was just measured.

Check that no old sealant has fallen into the coolant passages or the oil returns. Debris left in a gallery travels to a bearing or a thermostat, and the failure it causes appears weeks later with no obvious connection to the gasket job.

FAQ

How do I know if I need this kit or 7000002541?

Compare the old head gasket with the head casting number. Send us photos and we will confirm.

Is the head gasket included?

Yes, this is a full set.

Do I need sealant with the head gasket?

No. The steel gasket is installed dry.

Are the gaskets reusable?

No. Gaskets and copper washers are single-use.

Related parts and categories

Browse the Baudouin gasket set category, and pair the kit with the 4M10G110 cylinder head 1005045623 or the 4M10G110 gasket kit 7000002541.

Description

Baudouin 4M10G110 Full Gasket Kit (1002224369). Sealing is the difference between a rebuild that finishes in one pass and one that waits a week for a missing washer. This set covers the head, manifolds, injectors and the small seals.

Confirm the kit matches the head casting revision, not only the engine model. Castings changed across production and the gasket followed.

Numbers beginning 1002 are numeric-series numbers used mainly on WP8 and WP9 assemblies and castings. On this engine, confirm the 4M10G110 application against the engine plate before ordering.

Use new head bolts and torque in three stages, then angle tighten in the factory sequence. Reused bolts reduce clamping load under load.

Ordering note. Inspection reports can be provided for castings and crankshafts on request, covering the measurements taken before packing.

Related reading: Head Gasket Failure Symptoms and How to Choose a Replacement

We Are 30 Years Diesel Engine Parts Supplier
BrandEPID
Warranty12 Months
Condition100%New
More ModelsWeichai: 4M10G110, and other Weichai series.
ShippingBy sea / air / express (DHL, FEDEX, TNT, UPS, EMS)
PackingStandard exporting packing or as required
Payment TermL/C, T/T, Western Union, Trade Assurance
Delivery Time3-7 days (depend on order)
Selling Point1. On-time Delivery   2. Genuine Quality Assurance   3. Professional Supplier

How to tell which specification you need

Put the old head gasket on a flat surface next to the new one. Fire ring position, coolant hole pattern and overall thickness are the three features that matter, and all three are visible when the two are side by side. If any of them differ, stop and check the head casting number before the engine is stripped.

Why the head gasket is the deciding part

The rest of the kit is common enough that two specifications can look identical on the bench. The head gasket is the part that must match the casting, and it is also the part whose failure causes the most damage. Spend the time comparing it before the engine comes apart.

Symptoms of a failed gasket set

  • Oil weeping from the pan rail or rear main
  • Coolant seeping at the pump or thermostat housing
  • Soot marks around manifold joints
  • Bubbles in the heat exchanger
  • Oil and coolant mixing
  • Compression loss between adjacent cylinders

Installation notes

  1. Clean every mating surface to bare metal.
  2. Check head and block deck flatness.
  3. Fit the steel head gasket dry.
  4. Use new head bolts and torque in the factory sequence.
  5. Apply anaerobic sealant only where specified.
  6. Recheck for leaks after the first heat cycle.

Head bolts and clamping load

Head bolts are torque-to-yield and must be replaced every time the head is removed. Reusing them is the most common reason a new gasket fails early, and the failure is usually blamed on the gasket rather than on the bolts.

Diagnosing which gasket failed

A head gasket failure consumes coolant and pressurises the cooling system. A manifold failure leaves soot tracks and a whistle under load. A rear seal failure leaves oil at the bell housing rather than at the pan. Identifying the failure tells you whether a full kit is needed at all.

Working safely on a marine engine

Never open a pressurised cooling system while hot. The expansion tank on a boat can be above head height, and releasing the cap can spray scalding coolant. Let the engine cool completely, then release slowly.

Storage and handling

Store the kit flat, dry and out of sunlight. Composite gaskets absorb moisture slowly, so a kit stored in a damp engine room should be inspected before fitting. Keep the head gasket in its carton until the deck is ready.

Photographs that identify the specification

Send one photo of the old head gasket on a flat surface with a ruler alongside, one of the head casting number and one of the engine plate. Those three images let our team confirm the specification with confidence instead of guessing from the model name.

Freight and consolidation

Kits are light and compact and consolidate well with liners or pistons. Tell us what else is in the shipment so the kit is packed on top and not crushed by heavy parts.

Preparing the surfaces before the gasket goes on

The best gasket in the world will not seal a surface that has old material on it. Scrape the block deck and head face to bare metal, then wipe both with a suitable solvent. Avoid rotary abrasive discs, which remove metal unevenly and change the flatness that was just measured.

Check that no old sealant has fallen into the coolant passages or the oil returns. Debris left in a gallery travels to a bearing or a thermostat, and the failure it causes appears weeks later with no obvious connection to the gasket job.

Related parts and categories

Browse the Baudouin gasket set category, and pair the kit with the 4M10G110 cylinder head 1005045623 or the 4M10G110 gasket kit 7000002541.

Detailed picture

Baudouin 4M10G110 Full Gasket Kit 1002224369 Marine Diesel Parts
Baudouin 4M10G110 Full Gasket Kit 1002224369 Marine Diesel Parts

Q&A

  • How do I know if I need this kit or 7000002541?

    Compare the old head gasket with the head casting number. Send us photos and we will confirm.

  • Is the head gasket included?

    Yes, this is a full set.

  • Do I need sealant with the head gasket?

    No. The steel gasket is installed dry.

  • Are the gaskets reusable?

    No. Gaskets and copper washers are single-use.

Why buy from EPID

EPID supplies diesel engine parts for Weichai, Baudouin, Yuchai, Caterpillar, Sinotruk, FAW Xichai and Cummins engines. Every order is checked against the original part number before packing, and our team can identify a part from a photo of the engine plate. Ask for a quotation with your model and quantity and we will reply within one working day.

send message

    • [recaptcha]

    Home Tel Mail Inquiry