< img height="1" width="1" style="display:none" src="https://www.facebook.com/tr?id=2042618782839916&ev=PageView&noscript=1" />
Diesel Engines & Parts
Weichai WP7 WP8 Crankshaft 1003084463 Diesel Engine Parts
Weichai WP7 WP8 Crankshaft 1003084463 Diesel Engine Parts

Weichai WP7 WP8 Crankshaft 1003084463 Diesel Engine Parts

Model: WP7 / WP8

Part Number: 1003084463

Brands: Weichai Power

Engine Model: WP7, WP7H, WP8, WP8H

Engine Type: Diesel

Scope of application: medium and heavy trucks, buses, construction machinery, generator sets

One of several crankshaft numbers in the family

The WP7 and WP8 engines carry several crankshaft numbers, and 1003084463 is one of them alongside 610800020218, 610800020228, 1000186869 and 1000208972. The differences are usually in the damper fixing or the flywheel flange, tied to a production revision rather than to journal dimensions.

A shaft from the wrong variant fits the block but will not accept your existing damper or flywheel. Photographs of both shaft ends resolve the question faster than any catalogue lookup.

Crankshaft duty in these engines

The WP7 and WP8 produce high torque from relatively low speed, so the shaft sees strong bending loads and torsional pulses from six firing cylinders. It carries the main and rod bearings, drives the oil pump and camshaft through the gear train and delivers torque to the flywheel.

Once a journal loses roundness the bearing cannot maintain an oil film, pressure falls and failure follows quickly. Journal condition is therefore measured on every shaft we supply.

Manufacturing checks

Every shaft is measured after grinding. The checks cover the dimensions that decide whether it survives service, not only the ones that decide whether it fits.

  • Journal diameter and ovality measured at multiple positions.
  • Fillet radius verified, because fatigue cracks start there.
  • Run-out and straightness checked on centres.
  • Thrust face measured for flatness and finish.
  • Hardness confirmed after nitriding.

Failure symptoms

Bearing noise and oil pressure are the indicators that matter, and the knock appears later than the pressure change does. By the time the knock is audible the journal is usually already damaged.

  • Oil pressure falling as the engine warms
  • Knock under load, quiet at idle
  • Bearing shells with copper showing
  • Scoring or heat tint on journals
  • Excessive end float
  • Metal on the magnetic plug

Assembly requirements

Measure before assembly, record the figures and confirm main bore alignment. A distorted tunnel wears new bearings within hours, and the shaft is usually blamed for a block problem.

  1. Measure every journal and check ovality.
  2. Confirm main bore alignment in the block.
  3. Check clearances with plastigauge at every journal.
  4. Lubricate and confirm free rotation by hand.
  5. Set end float with the thrust bearing fitted.
  6. Replace a tired damper.

Choosing the correct shaft

Match the part number, the journal size and the shells you intend to fit. Mixing a reground shaft with standard shells guarantees failure. Give us the bearing part numbers and we will confirm the journal size before shipping.

Damper and torsional vibration

A six-cylinder crankshaft twists and untwists several times per revolution. The damper absorbs that oscillation; when its rubber perishes, the oscillation reaches the shaft and cracks begin at the fillets. Inspect the damper whenever the shaft is out.

Oil supply and rear seal surfaces

The rear main bearing receives oil through a gallery that crosses the block. If that gallery is left partially blocked after cleaning, the rear bearing runs dry first and the shaft shows heat marks exactly there.

Freight and crating

Shafts are bolted into braced crates with journals sleeved and lifting points marked. Tell us whether the shaft travels with a block so we can plan the load.

Protecting the shaft in service

Lubrication and vibration control decide crankshaft life. Use the specified oil, change it at the severe-duty interval and never run with a leaking injector that dilutes the oil.

Bearing shell selection and clearance

Shells come in standard and undersize grades and the grade must match the journal after any regrind. Check clearance with plastigauge at every journal and record the figures. One undersize journal among six is easy to miss, and running the engine in that state destroys the shaft within a few thousand kilometres.

Why the flywheel end matters

The flywheel flange carries the full engine torque into the gearbox, so a worn or corroded flange face causes clutch or converter problems that look unrelated to the crankshaft. Inspect the flange face and pilot bore when the shaft arrives, and protect them during installation.

Storage before fitting

Store the shaft in its crate, oiled and sleeved, until the block is ready. A shaft left on a workshop floor collects grit that finds its way into the bearings, and a shaft standing on end can be bent by its own weight.

FAQ

How do I choose between the shaft variants?

Compare the damper fixing and flywheel flange, or send us photos of both ends.

Is the shaft nitrided?

Yes, journals and fillets are nitrided.

Can the shaft be reground?

Only if enough hardened layer remains.

Should I replace the damper?

Strongly recommended with a new shaft.

Related parts and categories

Explore the Weichai crankshaft category, and complete the bottom end with the WP7 and WP8 crankshaft 1000186869 or the WP8 cylinder block 1001854444.

Description

Weichai WP7 Crankshaft (1003084463). Everything the engine produces passes through this shaft. Journals, fillets and the damper interface all decide how long the bearings survive, and all three are measurable before assembly.

Measure ovality at several positions along each journal, not at one point. A journal can read the correct diameter and still be oval by a few hundredths, which collapses the oil film twice per revolution.

Numbers beginning 1003 belong to the numeric series used across WP7, WP8 and WP9. The engine plate is the fastest way to confirm which revision applies. On this engine, confirm the WP7 application against the engine plate before ordering.

Fit a new torsional damper with the shaft. A perished damper sends the same oscillation into the new crankshaft and cracks it at the fillets.

Ordering note. For fleet customers, a consolidated stock list can be quoted against the engine plates in service, which usually exposes duplicated part numbers across similar units.

Related reading: Crankshaft Inspection: Journals, Fillets and Regrinding

We Are 30 Years Diesel Engine Parts Supplier
BrandEPID
Warranty12 Months
Condition100%New
More ModelsWeichai: WP7, WP7H, WP8, WP8H, and other Weichai series.
ShippingBy sea / air / express (DHL, FEDEX, TNT, UPS, EMS)
PackingStandard exporting packing or as required
Payment TermL/C, T/T, Western Union, Trade Assurance
Delivery Time3-7 days (depend on order)
Selling Point1. On-time Delivery   2. Genuine Quality Assurance   3. Professional Supplier

Manufacturing checks

Every shaft is measured after grinding. The checks cover the dimensions that decide whether it survives service, not only the ones that decide whether it fits.

  • Journal diameter and ovality measured at multiple positions.
  • Fillet radius verified, because fatigue cracks start there.
  • Run-out and straightness checked on centres.
  • Thrust face measured for flatness and finish.
  • Hardness confirmed after nitriding.

Failure symptoms

Bearing noise and oil pressure are the indicators that matter, and the knock appears later than the pressure change does. By the time the knock is audible the journal is usually already damaged.

  • Oil pressure falling as the engine warms
  • Knock under load, quiet at idle
  • Bearing shells with copper showing
  • Scoring or heat tint on journals
  • Excessive end float
  • Metal on the magnetic plug

Assembly requirements

Measure before assembly, record the figures and confirm main bore alignment. A distorted tunnel wears new bearings within hours, and the shaft is usually blamed for a block problem.

  1. Measure every journal and check ovality.
  2. Confirm main bore alignment in the block.
  3. Check clearances with plastigauge at every journal.
  4. Lubricate and confirm free rotation by hand.
  5. Set end float with the thrust bearing fitted.
  6. Replace a tired damper.

Choosing the correct shaft

Match the part number, the journal size and the shells you intend to fit. Mixing a reground shaft with standard shells guarantees failure. Give us the bearing part numbers and we will confirm the journal size before shipping.

Damper and torsional vibration

A six-cylinder crankshaft twists and untwists several times per revolution. The damper absorbs that oscillation; when its rubber perishes, the oscillation reaches the shaft and cracks begin at the fillets. Inspect the damper whenever the shaft is out.

Oil supply and rear seal surfaces

The rear main bearing receives oil through a gallery that crosses the block. If that gallery is left partially blocked after cleaning, the rear bearing runs dry first and the shaft shows heat marks exactly there.

Freight and crating

Shafts are bolted into braced crates with journals sleeved and lifting points marked. Tell us whether the shaft travels with a block so we can plan the load.

Protecting the shaft in service

Lubrication and vibration control decide crankshaft life. Use the specified oil, change it at the severe-duty interval and never run with a leaking injector that dilutes the oil.

Bearing shell selection and clearance

Shells come in standard and undersize grades and the grade must match the journal after any regrind. Check clearance with plastigauge at every journal and record the figures. One undersize journal among six is easy to miss, and running the engine in that state destroys the shaft within a few thousand kilometres.

Why the flywheel end matters

The flywheel flange carries the full engine torque into the gearbox, so a worn or corroded flange face causes clutch or converter problems that look unrelated to the crankshaft. Inspect the flange face and pilot bore when the shaft arrives, and protect them during installation.

Storage before fitting

Store the shaft in its crate, oiled and sleeved, until the block is ready. A shaft left on a workshop floor collects grit that finds its way into the bearings, and a shaft standing on end can be bent by its own weight.

Related parts and categories

Explore the Weichai crankshaft category, and complete the bottom end with the WP7 and WP8 crankshaft 1000186869 or the WP8 cylinder block 1001854444.

Detailed picture

Weichai WP7 WP8 Crankshaft 1003084463 Diesel Engine Parts
Weichai WP7 WP8 Crankshaft 1003084463 Diesel Engine Parts

Q&A

  • How do I choose between the shaft variants?

    Compare the damper fixing and flywheel flange, or send us photos of both ends.

  • Is the shaft nitrided?

    Yes, journals and fillets are nitrided.

  • Can the shaft be reground?

    Only if enough hardened layer remains.

  • Should I replace the damper?

    Strongly recommended with a new shaft.

Why buy from EPID

EPID supplies diesel engine parts for Weichai, Baudouin, Yuchai, Caterpillar, Sinotruk, FAW Xichai and Cummins engines. Every order is checked against the original part number before packing, and our team can identify a part from a photo of the engine plate. Ask for a quotation with your model and quantity and we will reply within one working day.

send message

    • [recaptcha]

    Home Tel Mail Inquiry