< img height="1" width="1" style="display:none" src="https://www.facebook.com/tr?id=2042618782839916&ev=PageView&noscript=1" />
Diesel Engines & Parts
Weichai WP13 Full Gasket Kit 1004220117 Engine Overhaul Set
Weichai WP13 Full Gasket Kit 1004220117 Engine Overhaul Set

Weichai WP13 Full Gasket Kit 1004220117 Engine Overhaul Set

Model: WP13

Part Number: 1004220117

Brands: Weichai Power

Engine Model: WP13, WP13.480, WP13.500, WP13.550, WP13.580

Engine Type: Diesel

Scope of application: heavy haulage trucks, mining dump trucks, construction machinery, generator sets

A gasket kit number in the WP13 family

The WP13 carries more than one full gasket kit number, and 1004220117 is one of them alongside 612700040018. The differences are concentrated in the head gasket, tied to a production revision of the cylinder head casting, while the pan and manifold gaskets remain largely common. That is why the old gasket and the casting number matter more than the model name when ordering.

What the kit contains

This is a complete sealing set for a rebuild, covering every joint that is opened during an overhaul. Buying the set instead of individual gaskets guarantees that no washer is forgotten, and one missing part produces a leak that appears only when the engine is hot and working.

  • Head gasket matched to the head casting.
  • Valve cover and manifold gaskets.
  • Oil pan gasket and timing cover seals.
  • Front and rear crank seals.
  • Water pump and thermostat housing seals.
  • Injector copper washers and small O-rings.

How to identify which kit you need

Compare the old head gasket with the new one before the engine is stripped. Fire ring position, coolant hole pattern and thickness decide compatibility, and all three are visible when the two gaskets are laid side by side on a flat surface. If any of them differ, stop and check the casting number.

Symptoms of a failed gasket set

Confirm which gasket has failed before ordering. Oil at the pan rail points to the pan gasket or rear main, coolant at the front points to the pump, soot around manifold joints points to manifold gaskets, and bubbles in the radiator point to the head gasket. Knowing the answer tells you whether a full kit is needed at all.

  • Oil weeping from the pan rail or rear main
  • Coolant seeping at the pump or thermostat housing
  • Soot marks around manifold joints
  • Bubbles in the radiator
  • Oil and coolant mixing
  • Compression loss between adjacent cylinders

Installation sequence

Preparation decides whether the gasket seals. Clean both surfaces to bare metal, check flatness, and confirm the head bolts are new before the head goes back on.

  1. Clean every mating surface to bare metal.
  2. Check head and block deck flatness.
  3. Fit the head gasket dry, without sealant.
  4. Use new head bolts and torque in the factory sequence.
  5. Apply anaerobic sealant only where specified.
  6. Recheck for leaks after the first heat cycle.

Why the head gasket fails first

The head gasket sees combustion pressure, coolant at temperature and returning oil at once, which no other gasket in the engine has to manage. When the engine overheats, the head expands unevenly and the clamping load shifts away from one area of the gasket. The leak begins as a small coolant loss and becomes a compression leak within a few hundred hours of running.

Common fitting mistakes

Reusing the pan gasket after inspecting the bearings, adding sealant to a head gasket and fitting manifold gaskets dry are the most common errors. Each produces a leak that appears only when the engine is hot and working, when the repair costs far more than the parts.

Storage and handling

Store the kit flat, dry and out of sunlight. Composite gaskets absorb moisture slowly, and a kit stored in a damp workshop should be inspected before fitting. Keep the head gasket in its carton rather than on a bench where it can be bent.

Freight and consolidation

Kits are light and compact, ideal to consolidate with liners or pistons. Tell us what else is in the shipment so the kit is packed on top and not crushed by a cylinder block.

After the rebuild

Retorque manifold bolts and check pan bolts after the first week. Keep coolant at the correct mixture to prevent liner pitting and repair any oil leak immediately, because oil soaking into a composite gasket eventually softens it.

Which gasket usually fails first

On a WP13 the head gasket is the usual failure, followed by manifold gaskets and the rear crank seal. Each has a different signature, and identifying it before the engine is opened tells you whether a full kit is needed or whether a single gasket will do the job.

Working on a hot engine

Never open a pressurised cooling system while hot. Release the cap slowly after the engine has cooled, because the coolant is well above boiling point when pressurised and can cause severe burns.

FAQ

Is the head gasket included?

Yes. This is a full set.

How do I choose between the WP13 kits?

Compare the old head gasket and the head casting number, or send us photos.

Do I need sealant with the head gasket?

No. It is installed dry.

Are the gaskets reusable?

No. Gaskets and copper washers are single-use.

Related parts and categories

Browse the Weichai gasket set category, and pair the kit with the WP13 full gasket kit 612700040018 or the WP13 cylinder head 612700040030.

Description

Weichai WP13 Full Gasket Kit (1004220117). The gasket set seals combustion, coolant and oil at every joint opened during a top-end repair. The head gasket inside it is the component that decides whether the job holds.

Confirm the kit matches the head casting revision, not only the engine model. Castings changed across production and the gasket followed.

Numbers beginning 1004 are numeric-series numbers used on later WP7 and WP8 production, where mounting detail changed without a change of nominal type. On this engine, confirm the WP13 application against the engine plate before ordering.

Use new head bolts and torque in three stages, then angle tighten in the factory sequence. Reused bolts reduce clamping load under load.

Ordering note. Lead time depends on whether the item is in stock or has to be produced; the position is confirmed before the order is accepted rather than after payment.

Related reading: Head Gasket Failure Symptoms and How to Choose a Replacement

We Are 30 Years Diesel Engine Parts Supplier
BrandEPID
Warranty12 Months
Condition100%New
More ModelsWeichai: WP13, WP13.480, WP13.500, WP13.550, WP13.580, and other Weichai series.
ShippingBy sea / air / express (DHL, FEDEX, TNT, UPS, EMS)
PackingStandard exporting packing or as required
Payment TermL/C, T/T, Western Union, Trade Assurance
Delivery Time3-7 days (depend on order)
Selling Point1. On-time Delivery   2. Genuine Quality Assurance   3. Professional Supplier

How to identify which kit you need

Compare the old head gasket with the new one before the engine is stripped. Fire ring position, coolant hole pattern and thickness decide compatibility, and all three are visible when the two gaskets are laid side by side on a flat surface. If any of them differ, stop and check the casting number.

Symptoms of a failed gasket set

Confirm which gasket has failed before ordering. Oil at the pan rail points to the pan gasket or rear main, coolant at the front points to the pump, soot around manifold joints points to manifold gaskets, and bubbles in the radiator point to the head gasket. Knowing the answer tells you whether a full kit is needed at all.

  • Oil weeping from the pan rail or rear main
  • Coolant seeping at the pump or thermostat housing
  • Soot marks around manifold joints
  • Bubbles in the radiator
  • Oil and coolant mixing
  • Compression loss between adjacent cylinders

Installation sequence

Preparation decides whether the gasket seals. Clean both surfaces to bare metal, check flatness, and confirm the head bolts are new before the head goes back on.

  1. Clean every mating surface to bare metal.
  2. Check head and block deck flatness.
  3. Fit the head gasket dry, without sealant.
  4. Use new head bolts and torque in the factory sequence.
  5. Apply anaerobic sealant only where specified.
  6. Recheck for leaks after the first heat cycle.

Why the head gasket fails first

The head gasket sees combustion pressure, coolant at temperature and returning oil at once, which no other gasket in the engine has to manage. When the engine overheats, the head expands unevenly and the clamping load shifts away from one area of the gasket. The leak begins as a small coolant loss and becomes a compression leak within a few hundred hours of running.

Common fitting mistakes

Reusing the pan gasket after inspecting the bearings, adding sealant to a head gasket and fitting manifold gaskets dry are the most common errors. Each produces a leak that appears only when the engine is hot and working, when the repair costs far more than the parts.

Storage and handling

Store the kit flat, dry and out of sunlight. Composite gaskets absorb moisture slowly, and a kit stored in a damp workshop should be inspected before fitting. Keep the head gasket in its carton rather than on a bench where it can be bent.

Freight and consolidation

Kits are light and compact, ideal to consolidate with liners or pistons. Tell us what else is in the shipment so the kit is packed on top and not crushed by a cylinder block.

After the rebuild

Retorque manifold bolts and check pan bolts after the first week. Keep coolant at the correct mixture to prevent liner pitting and repair any oil leak immediately, because oil soaking into a composite gasket eventually softens it.

Which gasket usually fails first

On a WP13 the head gasket is the usual failure, followed by manifold gaskets and the rear crank seal. Each has a different signature, and identifying it before the engine is opened tells you whether a full kit is needed or whether a single gasket will do the job.

Working on a hot engine

Never open a pressurised cooling system while hot. Release the cap slowly after the engine has cooled, because the coolant is well above boiling point when pressurised and can cause severe burns.

Related parts and categories

Browse the Weichai gasket set category, and pair the kit with the WP13 full gasket kit 612700040018 or the WP13 cylinder head 612700040030.

Detailed picture

Weichai WP13 Full Gasket Kit 1004220117 Engine Overhaul Set
Weichai WP13 Full Gasket Kit 1004220117 Engine Overhaul Set

Q&A

  • Is the head gasket included?

    Yes. This is a full set.

  • How do I choose between the WP13 kits?

    Compare the old head gasket and the head casting number, or send us photos.

  • Do I need sealant with the head gasket?

    No. It is installed dry.

  • Are the gaskets reusable?

    No. Gaskets and copper washers are single-use.

Why buy from EPID

EPID supplies diesel engine parts for Weichai, Baudouin, Yuchai, Caterpillar, Sinotruk, FAW Xichai and Cummins engines. Every order is checked against the original part number before packing, and our team can identify a part from a photo of the engine plate. Ask for a quotation with your model and quantity and we will reply within one working day.

send message

    • [recaptcha]

    Home Tel Mail Inquiry