



Model: WD615 / WP10
Part Number: 612600070365
Brands: Weichai Power
Engine Model: WD615, WD615E2, WD10, WP10, WP10G
Engine Type: Diesel
Scope of application: heavy trucks, buses, construction machinery, generator sets
Part 612600070365 is a gear-type oil pump used across the WD615 and WP10 family, the six-cylinder engines that power a large share of the heavy trucks working in export markets. It draws oil from the sump, pressurises it and feeds the main and rod bearings, the camshaft, the valve train and the piston cooling jets.
The pump is driven from the front gear train and fitted with an integrated relief valve. When it wears, the effect is gradual: pressure falls at hot idle first, oil temperature rises, and bearing wear begins long before the driver notices anything at the wheel.
The pump fits WD615 and WP10 engines in heavy trucks, buses, loaders and generator sets. Confirm the engine plate and the old pump number before ordering. Industrial and marine versions can use a different pick-up arrangement even when the pump body is the same casting, and a mismatched pick-up starves the pump under load.
Every pump is run on a test bench rather than only inspected, because the difference between a serviceable pump and a worn one is a few percent of flow that no visual check reveals.
Low pressure is the headline symptom, but the circumstances tell you what is actually wrong. Pressure that is low only when hot points as much to worn bearings as to a worn pump, while pressure that recovers instantly with engine speed points to the relief valve or pump clearances.
Check oil level and condition, replace the filter, inspect the strainer, then measure pressure with a mechanical gauge. Only after those steps should the relief valve and the pump come under suspicion, because a blocked strainer and a faulty sender both produce identical readings.
Record cold idle, hot idle and rated speed. That three-point record is far more useful for diagnosis than a single figure at idle, and it costs nothing to note in the service book.
Priming is the step most often skipped, and it is the one that decides whether the bearings survive the first minute after a rebuild.
On these engines the pump also supplies the piston cooling jets. A pump that holds pressure but has lost volume still allows crown temperatures to climb, and the damage appears as a scored or cracked piston rather than as low oil pressure. If pistons have failed without an obvious cause, measure flow before blaming the pistons.
Match the part number, the engine rating and the drive type. If the engine has been rebuilt with a replacement front cover, check that the mounting face and drive gear match. Send a photo of the old pump beside a ruler and we will confirm the casting before shipping.
Most premature failures come from contaminated oil. Use the specified grade, change it at the severe-duty interval and never run with a leaking injector that thins the oil with diesel. Keep the cooling system healthy, because sustained overheating reduces oil film strength at the bearings.
Fleets that run regular oil analysis catch bearing wear before pressure starts to fall. Rising iron and lead in the report indicate the oil film is breaking down somewhere in the engine, and the pump is one of the first parts worth checking. Analysis is cheap compared with a crankshaft.
Yes, the mounting gasket and O-ring are supplied.
Yes. A blocked strainer, stuck relief valve, worn bearings or a faulty sender all mimic pump failure.
The pump comes with its drive gear fitted and timed as original.
At every major overhaul, or whenever the front cover is removed.
Browse the Weichai pump category, and pair the pump with the WD615 oil pump 61500070030 or the WD615 crankshaft 1000072536.
Weichai WD615 Oil Pump (612600070365). Lubrication starts here. The gear set, relief valve and drive must all match the housing, and a mismatch shows up as low pressure from the first start.
Compare the old pump number and photograph the drive end. A pump with the wrong drive bolts up and fails to feed correctly.
Numbers beginning 6126 belong to the generation shared with the WD618 and early WP12 engines. Parts in this block were revised several times, so the casting or housing is the reliable identifier rather than the number alone. On this engine, confirm the WD615 application against the engine plate before ordering.
Replace the suction-side O-rings and gaskets with the pump. A hardened O-ring at the pick-up joint draws air and reproduces exactly the symptom the new pump was meant to cure.
Ordering note. Mixed pallets are accepted, so a single order can carry the block, the gasket set and the small seals together instead of arriving in three shipments.
Related reading: Oil Pump Diagnosis: Low Pressure, Wear and Replacement
| We Are 30 Years Diesel Engine Parts Supplier | |
| Brand | EPID |
| Warranty | 12 Months |
| Condition | 100%New |
| More Models | Weichai: WD615, WD615E2, WD10, WP10, WP10G, and other Weichai series. |
| Shipping | By sea / air / express (DHL, FEDEX, TNT, UPS, EMS) |
| Packing | Standard exporting packing or as required |
| Payment Term | L/C, T/T, Western Union, Trade Assurance |
| Delivery Time | 3-7 days (depend on order) |
| Selling Point | 1. On-time Delivery 2. Genuine Quality Assurance 3. Professional Supplier |
Every pump is run on a test bench rather than only inspected, because the difference between a serviceable pump and a worn one is a few percent of flow that no visual check reveals.
Low pressure is the headline symptom, but the circumstances tell you what is actually wrong. Pressure that is low only when hot points as much to worn bearings as to a worn pump, while pressure that recovers instantly with engine speed points to the relief valve or pump clearances.
Check oil level and condition, replace the filter, inspect the strainer, then measure pressure with a mechanical gauge. Only after those steps should the relief valve and the pump come under suspicion, because a blocked strainer and a faulty sender both produce identical readings.
Record cold idle, hot idle and rated speed. That three-point record is far more useful for diagnosis than a single figure at idle, and it costs nothing to note in the service book.
Priming is the step most often skipped, and it is the one that decides whether the bearings survive the first minute after a rebuild.
On these engines the pump also supplies the piston cooling jets. A pump that holds pressure but has lost volume still allows crown temperatures to climb, and the damage appears as a scored or cracked piston rather than as low oil pressure. If pistons have failed without an obvious cause, measure flow before blaming the pistons.
Match the part number, the engine rating and the drive type. If the engine has been rebuilt with a replacement front cover, check that the mounting face and drive gear match. Send a photo of the old pump beside a ruler and we will confirm the casting before shipping.
Most premature failures come from contaminated oil. Use the specified grade, change it at the severe-duty interval and never run with a leaking injector that thins the oil with diesel. Keep the cooling system healthy, because sustained overheating reduces oil film strength at the bearings.
Fleets that run regular oil analysis catch bearing wear before pressure starts to fall. Rising iron and lead in the report indicate the oil film is breaking down somewhere in the engine, and the pump is one of the first parts worth checking. Analysis is cheap compared with a crankshaft.
Browse the Weichai pump category, and pair the pump with the WD615 oil pump 61500070030 or the WD615 crankshaft 1000072536.




Yes, the mounting gasket and O-ring are supplied.
Yes. A blocked strainer, stuck relief valve, worn bearings or a faulty sender all mimic pump failure.
The pump comes with its drive gear fitted and timed as original.
At every major overhaul, or whenever the front cover is removed.
EPID supplies diesel engine parts for Weichai, Baudouin, Yuchai, Caterpillar, Sinotruk, FAW Xichai and Cummins engines. Every order is checked against the original part number before packing, and our team can identify a part from a photo of the engine plate. Ask for a quotation with your model and quantity and we will reply within one working day.