< img height="1" width="1" style="display:none" src="https://www.facebook.com/tr?id=2042618782839916&ev=PageView&noscript=1" />
Diesel Engines & Parts
Baudouin 4M10G88 Full Gasket Kit 1002087742 Marine Diesel Parts
Baudouin 4M10G88 Full Gasket Kit 1002087742 Marine Diesel Parts

Baudouin 4M10G88 Full Gasket Kit 1002087742 Marine Diesel Parts

Model: 4M10G88

Part Number: 1002087742

Brands: Baudouin

Engine Model: 4M10G88

Engine Type: Marine and industrial diesel

Scope of application: marine propulsion, marine auxiliary, generator sets

A second gasket specification for the G88

As with the G70, Baudouin used more than one gasket specification for the 4M10G88 across production periods and head castings. Kit 1002087742 is the alternative to 7000002268, and the correct choice depends on what is fitted to the engine rather than on the model name.

We always ask for the old gasket number and a photograph of the head face. A kit that looks right on the shelf can be wrong at the head face, and the leak that follows is blamed on the gasket rather than the specification.

What the kit contains

  • Head gasket for the matching head casting.
  • Valve cover and manifold gaskets.
  • Oil pan gasket and timing cover seals.
  • Crank seals and pump seals.
  • Injector copper washers and small O-rings.

Identifying which specification you need

Compare the old head gasket with the new one before stripping the engine. Fire ring position, coolant hole pattern and thickness are the three features that matter. If they differ, check the head casting number before proceeding.

Symptoms of a failed gasket set

  • Oil weeping from the pan rail or rear main
  • Coolant seeping at the pump or thermostat housing
  • Soot marks around manifold joints
  • Bubbles in the heat exchanger
  • Oil and coolant mixing
  • Compression loss between adjacent cylinders

Installation notes

  1. Clean every mating surface to bare metal.
  2. Check head and block deck flatness.
  3. Fit the steel head gasket dry.
  4. Use new head bolts and torque in the factory sequence.
  5. Apply anaerobic sealant only where specified.
  6. Recheck for leaks after the first heat cycle.

Head bolts and clamping load

Head bolts are torque-to-yield and must be replaced every time. Reusing them is the most common reason a new gasket fails early.

Which gasket failed first

A head gasket failure consumes coolant; a manifold failure leaves soot; a rear seal failure leaves oil at the bell housing. Identifying the failure tells you whether a full kit is needed.

Working safely on a marine engine

Never open a pressurised cooling system while hot. Let the engine cool completely, then release the cap slowly.

Storage and handling

Store flat, dry and out of sunlight. Composite gaskets absorb moisture slowly, so inspect a kit that has been stored in a damp engine room.

Manifold and coolant passage checks

Check the manifold face for warping and confirm that the coolant holes in the new gasket align with the passages in the head and manifold. A blocked passage causes a local hot spot that later looks like a head failure.

Parts worth replacing while open

When the gasket set is being fitted, consider the thermostat, water pump seal and injector copper washers. These are inexpensive parts whose failure would mean opening the same joints again.

Freight and consolidation

Kits are light and compact and consolidate well with liners or pistons. Tell us what else is in the shipment so the kit is packed on top.

Comparing the two G88 gasket specifications

As with the G70, the difference between the two G88 kits is concentrated in the head gasket. Coolant hole position and fire ring geometry differ between head castings, and a gasket from the wrong specification blocks or bypasses a coolant passage.

That failure is particularly unpleasant because it does not leak immediately. The engine runs hotter in one area, and the damage appears as a warped deck or a cracked seat some hundreds of hours later, long after the gasket was fitted and assumed to be correct.

What to photograph before ordering

Take one photo of the old head gasket on a flat surface with a ruler alongside, one of the head casting number and one of the engine plate. Those three images let our team identify the specification with confidence rather than guessing from the model name.

Returning the old gasket for identification

If you cannot identify the specification from photographs, keep the old head gasket and send it with the order. A used gasket is easy to ship and far more reliable than a description over the phone. Mark the top face so it is not mistaken for a new part on arrival.

FAQ

How do I know if I need this kit or 7000002268?

Compare the old head gasket and the head casting number. Send us a photo and we will confirm.

Is the head gasket included?

Yes, this is a full set.

Do I need sealant with the head gasket?

No. The steel gasket is installed dry.

Are the gaskets reusable?

No. Gaskets and copper washers are single-use.

Related parts and categories

Browse the Baudouin gasket set category, and pair the kit with the 4M10G88 cylinder head 1004882176 or the 4M10G88 overhaul kit 1004934489.

Description

Baudouin 4M10G88 Full Gasket Kit (1002087742). Sealing is the difference between a rebuild that finishes in one pass and one that waits a week for a missing washer. This set covers the head, manifolds, injectors and the small seals.

Confirm the kit matches the head casting revision, not only the engine model. Castings changed across production and the gasket followed.

Numbers beginning 1002 are numeric-series numbers used mainly on WP8 and WP9 assemblies and castings. On this engine, confirm the 4M10G88 application against the engine plate before ordering.

Install the head gasket dry unless the manual says otherwise. Sealant prevents composite and MLS gaskets from seating correctly.

Ordering note. Photographs of the actual unit can be sent before dispatch on request. That is the cheapest way to avoid a return when a casting revision is in doubt.

Related reading: Head Gasket Failure Symptoms and How to Choose a Replacement

We Are 30 Years Diesel Engine Parts Supplier
BrandEPID
Warranty12 Months
Condition100%New
More ModelsWeichai: 4M10G88, and other Weichai series.
ShippingBy sea / air / express (DHL, FEDEX, TNT, UPS, EMS)
PackingStandard exporting packing or as required
Payment TermL/C, T/T, Western Union, Trade Assurance
Delivery Time3-7 days (depend on order)
Selling Point1. On-time Delivery   2. Genuine Quality Assurance   3. Professional Supplier

Identifying which specification you need

Compare the old head gasket with the new one before stripping the engine. Fire ring position, coolant hole pattern and thickness are the three features that matter. If they differ, check the head casting number before proceeding.

Symptoms of a failed gasket set

  • Oil weeping from the pan rail or rear main
  • Coolant seeping at the pump or thermostat housing
  • Soot marks around manifold joints
  • Bubbles in the heat exchanger
  • Oil and coolant mixing
  • Compression loss between adjacent cylinders

Installation notes

  1. Clean every mating surface to bare metal.
  2. Check head and block deck flatness.
  3. Fit the steel head gasket dry.
  4. Use new head bolts and torque in the factory sequence.
  5. Apply anaerobic sealant only where specified.
  6. Recheck for leaks after the first heat cycle.

Head bolts and clamping load

Head bolts are torque-to-yield and must be replaced every time. Reusing them is the most common reason a new gasket fails early.

Which gasket failed first

A head gasket failure consumes coolant; a manifold failure leaves soot; a rear seal failure leaves oil at the bell housing. Identifying the failure tells you whether a full kit is needed.

Working safely on a marine engine

Never open a pressurised cooling system while hot. Let the engine cool completely, then release the cap slowly.

Storage and handling

Store flat, dry and out of sunlight. Composite gaskets absorb moisture slowly, so inspect a kit that has been stored in a damp engine room.

Manifold and coolant passage checks

Check the manifold face for warping and confirm that the coolant holes in the new gasket align with the passages in the head and manifold. A blocked passage causes a local hot spot that later looks like a head failure.

Parts worth replacing while open

When the gasket set is being fitted, consider the thermostat, water pump seal and injector copper washers. These are inexpensive parts whose failure would mean opening the same joints again.

Freight and consolidation

Kits are light and compact and consolidate well with liners or pistons. Tell us what else is in the shipment so the kit is packed on top.

Comparing the two G88 gasket specifications

As with the G70, the difference between the two G88 kits is concentrated in the head gasket. Coolant hole position and fire ring geometry differ between head castings, and a gasket from the wrong specification blocks or bypasses a coolant passage.

That failure is particularly unpleasant because it does not leak immediately. The engine runs hotter in one area, and the damage appears as a warped deck or a cracked seat some hundreds of hours later, long after the gasket was fitted and assumed to be correct.

What to photograph before ordering

Take one photo of the old head gasket on a flat surface with a ruler alongside, one of the head casting number and one of the engine plate. Those three images let our team identify the specification with confidence rather than guessing from the model name.

Returning the old gasket for identification

If you cannot identify the specification from photographs, keep the old head gasket and send it with the order. A used gasket is easy to ship and far more reliable than a description over the phone. Mark the top face so it is not mistaken for a new part on arrival.

Related parts and categories

Browse the Baudouin gasket set category, and pair the kit with the 4M10G88 cylinder head 1004882176 or the 4M10G88 overhaul kit 1004934489.

Detailed picture

Baudouin 4M10G88 Full Gasket Kit 1002087742 Marine Diesel Parts
Baudouin 4M10G88 Full Gasket Kit 1002087742 Marine Diesel Parts

Q&A

  • How do I know if I need this kit or 7000002268?

    Compare the old head gasket and the head casting number. Send us a photo and we will confirm.

  • Is the head gasket included?

    Yes, this is a full set.

  • Do I need sealant with the head gasket?

    No. The steel gasket is installed dry.

  • Are the gaskets reusable?

    No. Gaskets and copper washers are single-use.

Why buy from EPID

EPID supplies diesel engine parts for Weichai, Baudouin, Yuchai, Caterpillar, Sinotruk, FAW Xichai and Cummins engines. Every order is checked against the original part number before packing, and our team can identify a part from a photo of the engine plate. Ask for a quotation with your model and quantity and we will reply within one working day.

send message

    • [recaptcha]

    Home Tel Mail Inquiry