< img height="1" width="1" style="display:none" src="https://www.facebook.com/tr?id=2042618782839916&ev=PageView&noscript=1" />
Diesel Engines & Parts
Baudouin 4M10G70 Full Gasket Kit 1001958651 Marine Diesel Parts
Baudouin 4M10G70 Full Gasket Kit 1001958651 Marine Diesel Parts
Baudouin 4M10G70 Full Gasket Kit 1001958651 Marine Diesel Parts

Baudouin 4M10G70 Full Gasket Kit 1001958651 Marine Diesel Parts

Model: 4M10G70

Part Number: 1001958651

Brands: Baudouin

Engine Model: 4M10G70

Engine Type: Marine and industrial diesel

Scope of application: marine propulsion, marine auxiliary, generator sets

A second gasket specification for the G70

Baudouin used more than one gasket specification for the 4M10G70 depending on production period and head casting. Kit 1001958651 is the alternative specification to 7000001981, and the correct choice depends on what is actually fitted to the engine rather than on the model name alone.

That is why we always ask for the old gasket number and a photograph of the head. A kit that looks right on the shelf can be wrong at the head face, and the leak that follows is blamed on the gasket rather than the specification.

What the kit contains

  • Head gasket for the matching head casting.
  • Valve cover and manifold gaskets.
  • Oil pan gasket and timing cover seals.
  • Crank seals, pump and thermostat housing seals.
  • Injector copper washers and small O-rings.

Kits ship flat in a rigid carton so the head gasket cannot be creased in transit.

Identifying which specification you need

Compare the old head gasket with the new one before stripping the engine. Fire ring position, coolant hole pattern and thickness are the three features that matter, and all three are visible side by side. If they differ, stop and check the head casting number before proceeding.

Symptoms of a failed gasket set

  • Oil weeping from the pan rail or rear main
  • Coolant seeping at the pump or thermostat housing
  • Soot marks around manifold joints
  • Bubbles in the heat exchanger
  • Oil and coolant mixing
  • Compression loss between adjacent cylinders

Installation notes

  1. Clean every mating surface to bare metal.
  2. Check head and block deck flatness.
  3. Fit the steel head gasket dry.
  4. Use new head bolts and torque in the factory sequence.
  5. Apply anaerobic sealant only where specified.
  6. Recheck for leaks after the first heat cycle.

Head bolts and clamping load

Head bolts are torque-to-yield and must be replaced every time. Reusing them is the most common reason a new gasket fails early, and the failure is usually blamed on the gasket rather than on the bolts.

Which gasket failed first

A head gasket failure consumes coolant and pressurises the system; a manifold failure leaves soot; a rear seal failure leaves oil at the bell housing. Identifying the failure tells you whether a full kit is needed at all.

Working safely on a marine engine

Never open a pressurised cooling system while hot. The expansion tank on a boat can be above head height, and releasing the cap can spray scalding coolant.

Storage and handling

Store flat, dry and out of sunlight. Composite gaskets absorb moisture slowly, so a kit stored in a damp engine room should be inspected before fitting.

Manifold surface condition

Check the manifold face for warping when the gasket is replaced. A manifold that has been hot can bow, and a new gasket on a bowed face leaks again within weeks. Machining the face flat is a small job compared with a second strip-down.

Coolant passage alignment

Some manifold gaskets also seal coolant passages. Confirm that the holes in the new gasket align with the passages before fitting, because a gasket from a different specification can block a passage and cause a local hot spot.

Freight and consolidation

Kits are light and compact and consolidate well with liners or pistons. Tell us what else is in the shipment so the kit is packed on top.

Comparing the two G70 gasket specifications

The two specifications differ mainly in the head gasket. One uses a fire ring geometry matched to an earlier head casting, the other to a later one. The manifold and pan gaskets are largely common, which is why a kit can look interchangeable until the head face is compared.

If the engine has been rebuilt before and the head replaced, the original engine plate no longer tells you which gasket is fitted. The head casting number and the old gasket are the reliable identifiers, and both are easy to photograph.

Why the head gasket is the deciding part

Everything else in a gasket kit is common enough that two specifications can look identical on the bench. The head gasket is the part that must match the casting, and it is also the part whose failure causes the most damage. Spend the time comparing it before the engine comes apart.

FAQ

How do I know if I need this kit or 7000001981?

Compare the old head gasket and the head casting number. Send us a photo and we will confirm.

Is the head gasket included?

Yes, this is a full set.

Do I need sealant with the head gasket?

No. The steel gasket is installed dry.

Are the gaskets reusable?

No. Gaskets and copper washers are single-use.

Related parts and categories

Browse the Baudouin gasket set category, and pair the kit with the 4M10G70 cylinder head 1004713403 or the 4M10G70 overhaul kit 1000156637.

Description

Baudouin 4M10G70 Full Gasket Kit (1001958651). This set covers the sealing surfaces disturbed during a rebuild. Its head gasket is matched to the head casting, and the small seals it includes are the ones most often forgotten.

Check that the injector copper washers and manifold gaskets in the kit suit your engine variant. Those are the parts most often found missing or wrong.

Numbers beginning 1001 belong to the numeric series introduced as the older 61xx numbers were superseded. Both numbers may describe the same physical part. On this engine, confirm the 4M10G70 application against the engine plate before ordering.

Install the head gasket dry unless the manual says otherwise. Sealant prevents composite and MLS gaskets from seating correctly.

Ordering note. Every shipment leaves with a packing list matched to the invoice, which matters when a rebuild is waiting on one seal and the whole pallet has to be cleared through customs.

Related reading: Head Gasket Failure Symptoms and How to Choose a Replacement

We Are 30 Years Diesel Engine Parts Supplier
BrandEPID
Warranty12 Months
Condition100%New
More ModelsWeichai: 4M10G70, and other Weichai series.
ShippingBy sea / air / express (DHL, FEDEX, TNT, UPS, EMS)
PackingStandard exporting packing or as required
Payment TermL/C, T/T, Western Union, Trade Assurance
Delivery Time3-7 days (depend on order)
Selling Point1. On-time Delivery   2. Genuine Quality Assurance   3. Professional Supplier

Identifying which specification you need

Compare the old head gasket with the new one before stripping the engine. Fire ring position, coolant hole pattern and thickness are the three features that matter, and all three are visible side by side. If they differ, stop and check the head casting number before proceeding.

Symptoms of a failed gasket set

  • Oil weeping from the pan rail or rear main
  • Coolant seeping at the pump or thermostat housing
  • Soot marks around manifold joints
  • Bubbles in the heat exchanger
  • Oil and coolant mixing
  • Compression loss between adjacent cylinders

Installation notes

  1. Clean every mating surface to bare metal.
  2. Check head and block deck flatness.
  3. Fit the steel head gasket dry.
  4. Use new head bolts and torque in the factory sequence.
  5. Apply anaerobic sealant only where specified.
  6. Recheck for leaks after the first heat cycle.

Head bolts and clamping load

Head bolts are torque-to-yield and must be replaced every time. Reusing them is the most common reason a new gasket fails early, and the failure is usually blamed on the gasket rather than on the bolts.

Which gasket failed first

A head gasket failure consumes coolant and pressurises the system; a manifold failure leaves soot; a rear seal failure leaves oil at the bell housing. Identifying the failure tells you whether a full kit is needed at all.

Working safely on a marine engine

Never open a pressurised cooling system while hot. The expansion tank on a boat can be above head height, and releasing the cap can spray scalding coolant.

Storage and handling

Store flat, dry and out of sunlight. Composite gaskets absorb moisture slowly, so a kit stored in a damp engine room should be inspected before fitting.

Manifold surface condition

Check the manifold face for warping when the gasket is replaced. A manifold that has been hot can bow, and a new gasket on a bowed face leaks again within weeks. Machining the face flat is a small job compared with a second strip-down.

Coolant passage alignment

Some manifold gaskets also seal coolant passages. Confirm that the holes in the new gasket align with the passages before fitting, because a gasket from a different specification can block a passage and cause a local hot spot.

Freight and consolidation

Kits are light and compact and consolidate well with liners or pistons. Tell us what else is in the shipment so the kit is packed on top.

Comparing the two G70 gasket specifications

The two specifications differ mainly in the head gasket. One uses a fire ring geometry matched to an earlier head casting, the other to a later one. The manifold and pan gaskets are largely common, which is why a kit can look interchangeable until the head face is compared.

If the engine has been rebuilt before and the head replaced, the original engine plate no longer tells you which gasket is fitted. The head casting number and the old gasket are the reliable identifiers, and both are easy to photograph.

Why the head gasket is the deciding part

Everything else in a gasket kit is common enough that two specifications can look identical on the bench. The head gasket is the part that must match the casting, and it is also the part whose failure causes the most damage. Spend the time comparing it before the engine comes apart.

Related parts and categories

Browse the Baudouin gasket set category, and pair the kit with the 4M10G70 cylinder head 1004713403 or the 4M10G70 overhaul kit 1000156637.

Detailed picture

Baudouin 4M10G70 Full Gasket Kit 1001958651 Marine Diesel Parts
Baudouin 4M10G70 Full Gasket Kit 1001958651 Marine Diesel Parts
Baudouin 4M10G70 Full Gasket Kit 1001958651 Marine Diesel Parts

Q&A

  • How do I know if I need this kit or 7000001981?

    Compare the old head gasket and the head casting number. Send us a photo and we will confirm.

  • Is the head gasket included?

    Yes, this is a full set.

  • Do I need sealant with the head gasket?

    No. The steel gasket is installed dry.

  • Are the gaskets reusable?

    No. Gaskets and copper washers are single-use.

Why buy from EPID

EPID supplies diesel engine parts for Weichai, Baudouin, Yuchai, Caterpillar, Sinotruk, FAW Xichai and Cummins engines. Every order is checked against the original part number before packing, and our team can identify a part from a photo of the engine plate. Ask for a quotation with your model and quantity and we will reply within one working day.

send message

    • [recaptcha]

    Home Tel Mail Inquiry